![background image](http://html1.mh-extra.com/html/foundry-networks/fastiron-edge-switch-x424/fastiron-edge-switch-x424_manual_2324269438.webp)
Foundry Configuration Guide for the FESX, FSX, and FWSX
17 - 10
© Foundry Networks, Inc.
December 2005
•
In filters apply to routes the Layer 3 Switch learns from its neighbor on the interface.
To apply RIP route filters to an interface, enter commands such as the following:
FastIron SuperX Router(config)# interface ethernet 1/2
FastIron SuperX Router(config-if-1/2)# ip rip filter-group in 2 3 4
Syntax:
[no] ip rip filter-group in | out <filter-list>
These commands apply RIP route filters 2, 3, and 4 to all routes learned from the RIP neighbor on port 1/2.
Displaying RIP Filters
To display the RIP filters configured on the router, enter the following command at any CLI level:
Syntax:
show ip rip
This display shows the following information.
Table 17.4: CLI Display of RIP Filter Information
This Field...
Displays...
Route filters
The rows underneath “RIP Route Filter Table” list the RIP route filters. If no RIP route filters are configured on
the device, the following message is displayed instead: “No Filters are configured in RIP Route Filter Table”.
Index
The filter number. You assign this number when you configure the
filter.
Action
The action the router takes if a RIP route packet matches the IP
address and sub-net mask of the filter. The action can be one of the
following:
•
deny – RIP route packets that match the address and network
mask information in the filter are dropped. If applied to an
interface’s outbound filter group, the filter prevents the router from
advertising the route on that interface. If applied to an interface’s
inbound filter group, the filter prevents the router from adding the
route to its IP route table.
•
permit – RIP route packets that match the address and network
mask information are accepted. If applied to an interface’s
outbound filter group, the filter allows the router to advertise the
route on that interface. If applied to an interface’s inbound filter
group, the filter allows the router to add the route to its IP route
table.
Route IP Address
The IP address of the route’s destination network or host.
FESX424 Router>
show ip rip
RIP Route Filter Table
Index Action Route IP Address Subnet Mask
1 deny any any
RIP Neighbor Filter Table
Index Action Neighbor IP Address
1 permit any
Summary of Contents for FastIron Edge Switch X424
