![background image](http://html1.mh-extra.com/html/foundry-networks/fastiron-edge-switch-x424/fastiron-edge-switch-x424_manual_2324269531.webp)
Configuring OSPF
December 2005
© Foundry Networks, Inc.
20 - 7
happens:
•
A second ASBR comes on-line
•
A second ASBR that is already on-line begins advertising an equivalent route to the same destination.
In either case above, the router with the higher router ID floods the AS External LSAs and the other router
flushes its equivalent AS External LSAs. For example, if Router D is offline, Router E is the only source for a
route to the external routing domain. When Router D comes on-line, it takes over flooding of the AS External
LSAs to Router F, while Router E flushes its equivalent AS External LSAs to Router F.
•
One of the ASBRs starts advertising a route that is no longer equivalent to the route the other ASBR is
advertising. In this case, the ASBRs each flood AS External LSAs. Since the LSAs either no longer have the
same cost or no longer have the same next-hop router, the LSAs are no longer equivalent, and the LSA
reduction feature no longer applies.
•
The ASBR with the higher router ID becomes unavailable or is reconfigured so that it is no longer an ASBR.
In this case, the other ASBR floods the AS External LSAs. For example, if Router D goes off-line, then Router
E starts flooding the AS with AS External LSAs for the route to Router F.
Support for OSPF RFC 2328 Appendix E
Foundry devices provide support for Appendix E in OSPF RFC 2328. Appendix E describes a method to ensure
that an OSPF router (such as aFoundry Layer 3 Switch) generates unique link state IDs for type-5 (External) link
state advertisements (LSAs) in cases where two networks have the same network address but different network
masks.
NOTE:
Support for Appendix E of RFC 2328 is enabled automatically and cannot be disabled. No user
configuration is required.
Normally, an OSPF router uses the network address alone for the link state ID of the link state advertisement
(LSA) for the network. For example, if the router needs to generate an LSA for network 10.1.2.3 255.0.0.0, the
router generates ID 10.1.2.3 for the LSA.
However, suppose that an OSPF router needs to generate LSAs for all the following networks:
•
10.0.0.0 255.0.0.0
•
10.0.0.0 255.255.0.0
•
10.0.0.0 255.255.255.0
All three networks have the same network address, 10.0.0.0. Without support for RFC 2328 Appendix E, an
OSPF router uses the same link state ID, 10.0.0.0, for the LSAs for all three networks. For example, if the router
generates an LSA with ID 10.0.0.0 for network 10.0.0.0 255.0.0.0, this LSA conflicts with the LSA generated for
network 10.0.0.0 255.255.0.0 or 10.0.0.0 255.255.255.0. The result is multiple LSAs that have the same ID but
that contain different route information.
When appendix E is supported, the router generates the link state ID for a network as follows:
1.
Does an LSA with the network address as its ID already exist?
•
No – Use the network address as the ID.
•
Yes – Go to Step 2.
2.
Compare the networks that have the same network address, to determine which network is more specific.
The more specific network is the one that has more contiguous one bits in its network mask. For example,
network 10.0.0.0 255.255.0.0 is more specific than network 10.0.0.0 255.0.0.0, because the first network has
16 ones bits (255.255.0.0) whereas the second network has only 8 ones bits (255.0.0.0).
•
For the less specific network, use the networks address as the ID.
•
For the more specific network, use the network’s broadcast address as the ID. The broadcast address is
the network address, with all ones bits in the host portion of the address. For example, the broadcast
address for network 10.0.0.0 255.255.0.0 is 10.0.0.255.
Summary of Contents for FastIron Edge Switch X424
