background image

Product Limited Warranty

Model No.

Seller:

Invoice No.

Distributer 

Stamp:

Customer Name:

Purchasing Date:

Customer Contact:

Distributer Phone:

Thank you for choosing our product. 

This product is warranted for three (3) years since the 

purchasing date for free repair of problems arising our of defects in workmanship while 
using in accordance with installation manual and usage indications for intended purposes.

If the product does not work properly within the warranty period, please contact your 
nearest service center. This certificate must be presented to obtain free service under 
this warranty.

Our company reserves the rights to replace the product by other similar models. We can fix 
or repair the product at a reasonable service charge, after expiration of warranty period.

Service charges shall be paid even during the warranty period, if breakage or damage is 
caused by any of the following events (including but without limitation).

1.

 The user’s negligence or mistake in operation, unreasonable repair or alteration.

2.

 Products are damaged by negligence or mistake during installation.

3.

 The movement of the installation location of the product.

4.

 Using the product outside of the intended use in residential housing or commercial hotels.

5.

 The use of non-specified power supplies n(voltage, rating pressure)

6.

 Dirt, sand and impurities are causing invalid operation.

7. 

Damages due to force majeure (including but notlimited to natural disaster) or 

other incidents.

8. 

The user fails to use in compliance with the warning or caution described in the 

installation manual.

Note:

Please fill in the information in the warranty card correctly. If there are mistakes, the 
warranty will be invalid. This  three year warranty for free of charge repair service is only for 
the items listed in the warranty.

The purchasing date is subject to the purchasing invoice or reciept.

Please keep this warranty and invoice/receipt available for repair or maintenance.

Summary of Contents for BID1000W





















Reviews: