background image

Important Safeguards

DANGER

 – 

To reduce the risk of electrocution:

1.

 Do not use while bathing.

2.

 Do not place or store product where it can fall or be pulled into a tub or sink.

3.

 Do not place in or drop into water or other liquid.

4. 

Do not reach for a product that has fallen into water. Unplug immediately.

5.

 Do not wash the main unit or electrical plug with water or detergent.

6.

 Do not handle the electrical plug with wet hands.

7.

 Do not put a hand or other staff over the outlet of air dryer or block the outlet of air dryer.

8.

 Never disassemble, repair or modify this product.

9.

 During installation, disassembly, repair and maintenance of the product,the power plug must be 

switched off and water supply be shut off.

WARNING

 – 

To reduce the risk of burns, electrocution, fire, or injury to persons.

1.

 Close supervision is necessary when this product is used by, on, or near children or invalids.

2.

 Use this product only for its intended use as described in this manual. Do not use attachments not 

recommended by the manufacturer.

3.

 Never operate this product if it has a damaged cord or plug, if it is not working properly, if it has been 

dropped or damaged, or dropped into water. Return the product to a service center for examination and repair.

4.

 Keep the cord away from heated surfaces.

5.

 Never use while sleeping or drowsy.

6.

 Never drop or insert any object into any opening or hose.

7.

 Do not use outdoors or operate where aerosol (spray) products are being used or where oxygen is 

being administered.

8.

 Connect this product to a properly grounded outlet only. See Grounding Instructions.

9.

 Do not throw cigarettes and other burning stuff into toilet, otherwise it might cause fire.

10.

This product is electric appliance, so it must be placed far away from water. Please don’t drench urine 

and      other liquid to it.

11.

 Do not lay on side or upside the product during the electrical circuit.

12.

 It is prohibited to use other electric appliances in the same socket.

13. 

It is forbidden to use the power extension or unstable loose outlet.

14.

 The old aging water supply hose can not be used, otherwise it might cause leakage, fire or electrical 

shock. Installation of the bidet seat should include specified components and new water supply hose.

READ ALL INSTRUCTIONS BEFORE USING

When using electrical products, especially when children are present, basic safety precautions should 
always be followed, including the following:

1.

 The appliance is not to be used by persons (including children) with reduced physical, sensory or mental 

capabilities, or lack of experience and knowledge, unless they have been given supervision or instruction.

2.

 Children being supervised not to play with the appliance.

3. 

This appliance can be used by children aged from 8 years and above and persons with reduced physical, 

sensory or mental capabilities or lack of experience and knowledge if they have been given supervision or 
instruction concerning use of the appliance in a safe way and understand the hazards involved.

4. 

Children shall not play with the appliance.

5.

 Cleaning and user maintenance shall not be made by children without supervision.

Summary of Contents for BID1000W





















Reviews: