Fisher Minute Mount 2 system Owner'S Manual Download Page 92

Page: 92 / 112

Lit. No. 44224, Rev. 14

August 15, 2011

MAINTENANCE

5. Select the hole in the rear of the T-frame that

is best aligned with the rear hole in the push
assembly and reinstall the rear fasteners.
Tighten all four fasteners to 250 ft-lb.

6. Raise and lower the blade several times. The

cutting edge should be contacting the level
surface across the full length of the cutting
edge.

7. Verify that the cutting edges remain in full

contact with the ground while the wings are
shifted from the scoop position to a retracted
(vee) position.

Complete this procedure as often as required
to provide even cutting edge wear. Replace the
cutting edge(s) on your XtremeV™ blade when
worn to within 1" of the carriage bolts.

Select the hole

best aligned with

the rear holes in

the push assembly

Summary of Contents for Minute Mount 2 system

















































































































Search results

Summary of Contents for Minute Mount 2 system

Reviews:

Related manuals for Minute Mount 2 system

Brands by name

Popular brands

Fisher Minute Mount 2 system, Owner'S Manual

Search results

Summary of Contents for Minute Mount 2 system

Reviews:

Related manuals for Minute Mount 2 system

Brands by name

Popular brands