Fisher Minute Mount 2 system Owner'S Manual Download Page 94

Page: 94 / 112

Lit. No. 44224, Rev. 14

August 15, 2011

MAINTENANCE

Fill
Plug

Drain
Cap

XLS Blades

XtremeV Blades

Drain
Cap

Fill
Plug

Drain
Plug

Straight Blades

XtremeV™, XLS™ and other Straight Blades:

With the Minute Mount

2 system attached to the

vehicle, activate the control. For straight blades,
any angle will do, but for XtremeV and XLS
blades, move blade wings to the fully retracted
(vee) position. Activate the control FLOAT function
and manually collapse the lift ram all the way.

Turn the control OFF. Remove the

ll plug. Fill the

reservoir to the top of the

ll hole and replace the

ll plug.

For

uid recommendations see the following

Annual Fluid Change section.

Summary of Contents for Minute Mount 2 system

















































































































Search results

Summary of Contents for Minute Mount 2 system

Reviews:

Related manuals for Minute Mount 2 system

Brands by name

Popular brands

Fisher Minute Mount 2 system, Owner'S Manual

Search results

Summary of Contents for Minute Mount 2 system

Reviews:

Related manuals for Minute Mount 2 system

Brands by name

Popular brands