Fisher Minute Mount 2 system Owner'S Manual Download Page 68

Page: 68 / 112

Lit. No. 44224, Rev. 14

August 15, 2011

OPERATING YOUR SNOWPLOW

6. Turn the control and vehicle ignition ON. Raise

the blade slightly from the jack stands. Turn
the control OFF, and remove the jack stands.

7. Stand 8' clear of the blade drop zone when

checking the height adjustment of the cutting
edge to the road surface.

DO NOT

store unused spacers on top of the

shoe holder.

1. Raise the blade 1' off the road surface, turn

the control OFF, and from in front of the blade,
place jack stands or sturdy blocking under the
cutting edge.

2. Turn the control ON and lower the blade onto

the jack stands or blocking. Turn the control
and vehicle ignition OFF.

3. Remove the linchpin, and slide the antiwear

shoe down and out of the shoe holder.

4. Remove one or more spacers from the shoe

stem and reinstall the shoe into the shoe
holder.

5. Reinstall the linchpin.

Summary of Contents for Minute Mount 2 system

















































































































Search results

Summary of Contents for Minute Mount 2 system

Reviews:

Related manuals for Minute Mount 2 system

Brands by name

Popular brands

Fisher Minute Mount 2 system, Owner'S Manual

Search results

Summary of Contents for Minute Mount 2 system

Reviews:

Related manuals for Minute Mount 2 system

Brands by name

Popular brands