Fisher Minute Mount 2 system Owner'S Manual Download Page 104 | Manualshive

Page: 104 / 112

background image

Lit. No. 44224, Rev. 14

105

August 15, 2011

MAINTENANCE

Use the following procedure to install
hydraulic hoses:

1. Screw

the

fl

are nut onto the

fi

tting

fl

are and

hand tighten.

2. Align the hose so there are no twists or sharp

bends and so it will not be pinched or pulled
by moving parts.

3. Using two wrenches, hold the hose in position

and tighten the

fl

are nut 1/8–1/4 turn beyond

hand tight. Final torque on the

fl

are nut should

be approximately 20 ft-lb.

4. Reinstall any protective hose wraps in their

original positions.

FUSE REPLACEMENT

The vehicle electrical system contains several
automotive blade-style fuses. The snowplow
park/turn and control power is covered by fuses in
the under hood snowplow wiring. The control fuse
is "hot" when the vehicle ignition switch is ON and
the electrical connections to the snowplow are
completed.

See the Harness Diagram applicable to the
electrical system on your snowplow at the end of
this manual for fuse ratings and locations.

The XtremeV™ hydraulic unit harness system
contains four automotive blade-style mini fuses.
The 3-solenoid harness (to Port B on the hydraulic
unit module) and 8-solenoid harness (to Port C)
each contain two 4-amp mini fuses.

The XLS™ hydraulic unit harness system contains
four automotive blade-style mini fuses. The
2-solenoid harness (to Port B on the hydraulic unit
module) and 6-solenoid harness (to Port C) each
contain two 4-amp mini fuses.

«
...
102
103
104
105
106
...
»

Summary of Contents for Minute Mount 2 system

















































































































Reviews:

No comments

Related manuals for Minute Mount 2 system

Brand: Waycon Pages: 8

Brand: Harken Hoister Pages: 12

Brand: Yamaha Pages: 2

Brand: Eclipse Pages: 6

Brand: Hama Pages: 6

Brand: Hama Pages: 2

Brand: IDS Pages: 22

Brand: M7 SPEED Pages: 11

Brand: PAC Pages: 4

Brand: PAC Pages: 4

SX-70 SODR-X-TRACTOR

Brand: Pace Pages: 2

Brand: PAC Pages: 8

Brand: PAC Pages: 5

Brand: UMBRA RIMORCHI Pages: 18

Brand: Vaisala Pages: 2

Brand: ABLE Pages: 20

Brand: Kia Pages: 385

Brand: Jackco Pages: 11

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands