Fisher Minute Mount 2 system Owner'S Manual Download Page 39 | Manualshive

Page: 39 / 112

background image

Lit. No. 44224, Rev. 14

40

August 15, 2011

STRAIGHT BLADE

OPERATING YOUR SNOWPLOW

Function Description of Operation

ON/OFF

Move the control power switch ON to activate the hydraulic system. Turn the control OFF to lock
the blade in place. This prevents accidental movement of the blade.

RAISE

Move the control lever up (forward) to raise the snowplow and cancel the FLOAT mode.

LOWER

Move the control lever down (back) to lower the snowplow. Release the lever to stop blade at
desired height.

FLOAT

Move the control lever down (back) and hold for 3/4 second to activate the FLOAT mode. Blade
will lower to ground surface and follow contour of surface as it dips or raises.
Cancel the FLOAT mode by momentarily placing the control in the

RAISE

position, turning the

control OFF or turning the vehicle ignition OFF. Angling left or right does not cancel FLOAT.

LEFT

Move the control lever straight to the left to angle the blade left.

RIGHT

Move the control lever straight to the right to angle the blade right.

«
...
37
38
39
40
41
...
»

Summary of Contents for Minute Mount 2 system

















































































































Reviews:

No comments

Related manuals for Minute Mount 2 system

Brand: Garland Pages: 36

Brand: 4MOMS Pages: 20

Brand: Accessory Power Pages: 36

Brand: Young Living Pages: 41

Brand: zenitech Pages: 16

Brand: HAI Pages: 2

Brand: Hanlong Pages: 26

Brand: IHP Pages: 2

5500DN - Phaser B/W Laser Printer

Brand: Xerox Pages: 2

3600B - Phaser B/W Laser Printer

Brand: Xerox Pages: 2

Brand: Abicor Binzel Pages: 44

Brand: Barker Pages: 2

Brand: Razorri Pages: 26

Brand: Graphite Pages: 44

Brand: DigiTech Pages: 15

Brand: Nauticam Pages: 22

Brand: AC Schnitzer Pages: 20

Brand: Echomaster Pages: 8

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands