manualshive.com logo in svg

Fike CyberCat 1016, Installation Manual

Share
Download
Fike CyberCat 1016 Installation Manual Download Page 69

 

 

4.0 INSTALLATION 

 

UL S2203 

CyberCat 254/1016 Installation Manual 

4-9 

FM 

 

P/N: 06-326 

Rev 14, 09/2015

 

4.11  INSTALL OPTIONAL MODULES 

Several optional modules can be installed onto the CyberCat controller to expand its operational capabilities.  
The modules contain static sensitive components; therefore, handle them by the edges only and avoid 
touching the integrated components.  Keep each module in  the protective static bag it was shipped in until 
time for installation.  Always ground yourself with a proper wrist strap before handling the module(s) to reduce 
the risk of damage due to static discharge. 

The following terminals are provided on the CyberCat controller, as shown on Exhibit 4-8, to allow connection 
of the optional modules: 

Terminal 

Module 

P12 

CRM4 Relay Module or Reverse Polarity Module 

P13 

CRM4 Relay Module or Reverse Polarity Module 

P15 

Supplemental Loop Module 

P16 

Supplemental Power Supply 

P20 

Network Modules (RS485 or Fiber Optic) 

 

All of the optional modules, except the DACT, must be installed prior to installing the CyberCat controller into 
the enclosure.  Refer to the installation instructions supplied with each module for specific installation 
instructions. 

Note:

 If the optional Internal DACT is installed, terminal P12 is no longer available for use.

 

Note:

 Modules installed in terminals P13 and P20 share the same mounting footprint on the CyberCat board and 

cannot be used simultaneously. 

P7

C   NC   NO

Alarm

P11

P10

P9

P8

P6

P2

C  NC  NO

Supervisory

C   NC  NO

Trouble

L

IN

E

 2

S

Y

S

 T

R

B

L

H

EAR

TBE

A

T

L

IN

E

 1

OPTIONAL

DACT

OPTIONAL

CRM4 RELAY

OR

REVERSE

POLARITY

MODULE

OPTIONAL CRM4 RELAY,

NETWORK MODULES (RS485

& FIBER), OR REVERSE

POLARITY MODULE

OPTIONAL

SUPPLEMENTAL
POWER SUPPLY

OPTIONAL

SUPPLEMENTAL

LOOP MODULE

 

Exhibit 4-8:  Mounting Locations for Optional Modules 

Summary of Contents for CyberCat 1016





































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands