manualshive.com logo in svg

Fike CyberCat 1016, Installation Manual

Share
Download
Fike CyberCat 1016 Installation Manual Download Page 35

 

 

3.0 SYSTEM COMPONENTS 

 

UL S2203 

CyberCat 254/1016 Installation Manual 

3-15 

FM 

 

P/N: 06-326 

Rev 14, 09/2015

 

 

Exhibit 3-20:  Five Card Plate 

 

Exhibit 3-16:  Single Card Plate 

 

Exhibit 3-17:  Two Card Plate 

 

Exhibit 3-18:  Three Card Plate 

 

Exhibit 3-19:  Four Card Plate 

 

Exhibit 3-21:  Fire-Phone Plate 

3.4 

OPTIONAL DEAD-FRONT COVER PLATES 

For enclosures equipped with dead-front doors, the following cover plates can be ordered to enable you to 
blank off any unused openings in the dead-front panel.  The cover plates are made of 18 gauge steel with a 
Red or Black enamel finish to match the enclosure. 

•

 

Single Card Cover Plate (P/N 10-2697-c) 

•

 

Four Card Cover Plate (P/N 10-2776-c) 

•

 

Two Card Cover Plate (P/N 10-2774-c) 

•

 

Five Card Cover Plate (P/N 10-2701-c) 

•

 

Three Card Cover Plate (P/N 10-2775-c) 

•

 

Fire-phone Opening Cover Plate (P/N 10-2766-c) 

c

 = plate color, 

R

ed or 

B

lack 

 

Summary of Contents for CyberCat 1016





































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands