Fike CyberCat 1016 Installation Manual Download Page 13

Page: 13 / 100

1.0 INTRODUCTION

UL S2203

CyberCat 254/1016 Installation Manual

1-3

P/N: 06-326

Rev 14, 09/2015

1.5

RELATED DOCUMENTATION

To obtain a complete understanding of the specific features of the CyberCat or to become familiar with related
functions in general, refer to the documentation listed below. Please reference the most current version or
the version noted on the label located on the product.

Exhibit 1-1: Related Documentation

Document Title

Part Number

DACT (P/N 10-2528 & 10-2476) Installation Instructions

06-479

Supplemental Power Supply (P/N 10-2474-P) Installation Instructions

06-340

Supplemental Loop Module (P/N 10-2473) Installation Instructions

06-339

Relay Module (P/N 10-2204) Installation Instructions

06-345

Reverse Polarity Module (P/N 10-2254) Installation Instructions

06-156

RS485 Network Module (P/N 10-2482) Installation Instructions

06-349

Fiber Optic Network Module (P/N 10-2624) Installation Instructions

06-387

Remote Display Unit Product Manual

06-610

Ethernet Module (P/N 10-074) Product Manual

06-388

Multi-Interface Module (P/N 10-2583) Product Manual

06-367

Intelligent Graphic Annunciator Product Manual

06-231

Firefighter’s Smoke Control Station Product Manual

06-447

Twenty Zone Remote Annunciator (P/N 10-2667) Product Manual

06-453

Six Zone Smoke Control Switch Card (P/N 10-2658) Product Manual

06-444

Input/Output Switch Card (P/N 10-2659) Product Manual

06-446

Twenty Zone Annunciator Card (P/N 10-2660) Product Manual

06-445

Solenoid Supervision and Protection Assembly (P/N 10-2360) Installation

06-344

Masterbox Supervisor (P/N 10-2413) Installation Instructions

06-229

VESDA Network Interface (P/N 68-023) Product Manual

06-158

Hand Held Programmer (P/N 10-2648) Operating Instructions

06-390

C-Linx Panel Configuration Software Manual

06-327

Standard Enclosure Installation Instructions

06-480

Solid Dead-front Door Installation Instructions

06-477

3 Module Dead-front Door Installation Instructions

06-478

Emergency Voice Alarm System Product Manual

06-557

Audio Control Card (P/N 10-2661) Product Manual

06-558

Fire-Phone Card (P/N 10-2728) Product Manual

06-559

Supplemental Fire-Phone Card (P/N 10-2730) Product Manual

06-560

Fire Command Center Enclosure Installation Instructions

06-570

Fire Command Center Enclosure, Option 2 Back-Box, Installation Instructions

06-607

Dead-Front Cover Plate, Installation Instructions

06-601

Relay Mounting Plate, Installation Instructions

06-619

Remote Audio Enclosure (1 Amp) Installation Instructions

06-597

Remote Audio Enclosure (3 Amp) Installation Instructions

06-572

Remote Audio Enclosure (5 Amp) Installation Instructions

06-573

Summary of Contents for CyberCat 1016





































































































Search results

Summary of Contents for CyberCat 1016

Reviews:

Brands by name

Popular brands

Fike CyberCat 1016, Installation Manual

Search results

Summary of Contents for CyberCat 1016

Reviews:

Brands by name

Popular brands