Fike CyberCat 1016 Installation Manual Download Page 5

Page: 5 / 100

TABLE OF CONTENTS

UL S2203

CyberCat 254/1016 Installation Manual

iii

P/N: 06-326

Rev 14, 09/2015

SECTION

DESCRIPTION

PAGE

3.6.15

Amplifier Card ................................................................................................................ 3-24

3.6.15.1

Class A Speaker Card ................................................................................................... 3-24

3.6.16

Relay Control Assembly ................................................................................................ 3-25

3.6.17

Relay Card ..................................................................................................................... 3-25

3.6.18

Class A Peripheral Bus Card ......................................................................................... 3-25

3.6.19

FCC Digital Paging Assembly ....................................................................................... 3-26

3.6.20

Local Operating Console ............................................................................................... 3-27

3.6.20.1

Audio Adjunct Panel ...................................................................................................... 3-27

3.7

Intelligent Detectors ....................................................................................................... 3-28

3.7.1

Photoelectric Smoke Detector ....................................................................................... 3-28

3.7.2

Ionization Smoke Detector ............................................................................................ 3-28

3.7.3

Photo/Heat Combination Detector ................................................................................. 3-29

3.7.4

Heat Detector ................................................................................................................ 3-29

3.7.5

Photoelectric Duct Detector ........................................................................................... 3-30

3.7.5.1

Duct Detector Housing .................................................................................................. 3-30

3.7.6

FAAST Aspirating Smoke Detector ............................................................................... 3-31

3.8

Detector Bases .............................................................................................................. 3-32

3.8.1

Four Inch Detector Base ................................................................................................ 3-32

3.8.2

Six Inch Detector Base .................................................................................................. 3-32

3.8.3

Sounder Base ................................................................................................................ 3-32

3.8.4

Relay Base .................................................................................................................... 3-32

3.9

Remote Testing and Notification Accessories ............................................................... 3-33

3.9.1

Remote Annunciator ...................................................................................................... 3-33

3.9.2

Remote Test Station ...................................................................................................... 3-33

3.9.3

Remote Test Station with Key ....................................................................................... 3-33

3.10

Addressable Modules .................................................................................................... 3-34

3.10.1

Mini Monitor Module ...................................................................................................... 3-34

3.10.2

Monitor Module .............................................................................................................. 3-34

3.10.3

Dual Monitor Module ..................................................................................................... 3-35

3.10.4

Addressable Pull Station ............................................................................................... 3-35

3.10.5

Conventional Zone Monitor Module .............................................................................. 3-35

3.10.6

Supervised Control Module ........................................................................................... 3-36

3.10.6.1

Solenoid Protection Assembly ....................................................................................... 3-36

3.10.6.2

Master-box Interface ...................................................................................................... 3-36

3.10.7

Relay Module ................................................................................................................. 3-37

3.11

Vesda High Level Interface ........................................................................................... 3-37

3.12

Programming and Configuration Equipment ................................................................. 3-37

3.12.1

IR Remote Tool ............................................................................................................. 3-37

3.12.2

Hand Held Programmer ................................................................................................. 3-38

3.12.3

C-Linx Software ............................................................................................................. 3-38

3.12.4

Interface Cable .............................................................................................................. 3-38

3.12.5

Interface Converter ........................................................................................................ 3-38

3.12.6

Interface Cable (USB to RS232) ................................................................................... 3-38

3.12.7

Interface Cable (USB) ................................................................................................... 3-38

3.13

Batteries and Battery Enclosures .................................................................................. 3-39

3.13.1

18 AH Battery Assembly ................................................................................................ 3-39

3.13.2

Batteries......................................................................................................................... 3-39

3.13.3

Battery Enclosures ........................................................................................................ 3-39

3.13.3.1

33 AH Battery Enclosure ............................................................................................... 3-39

3.13.3.2

75 AH Battery Enclosure ............................................................................................... 3-39

Summary of Contents for CyberCat 1016





































































































Search results

Summary of Contents for CyberCat 1016

Reviews:

Brands by name

Popular brands

Fike CyberCat 1016, Installation Manual

Search results

Summary of Contents for CyberCat 1016

Reviews:

Brands by name

Popular brands