manualshive.com logo in svg

Fiery E-41, Installation And Service Manual

Share
Download
Fiery E-41 Installation And Service Manual Download Page 76

S

ERVICE

 P

ROCEDURES

76

7. If a monitor is connected to the E-41:

• When the Log On to Windows dialog box appears on the monitor, type 

Administrator

 in 

the user name field, type 

Fiery.1

 in the password field, and then press Enter on 

the keyboard. 

N

OTE

: 

Type 

Fiery.1

 exactly as shown. The password is case-sensitive; for example,

 

fiery.1

 will not work. 

• Wait for Idle to display on FieryBar on the monitor. 

If the E-41 is not connected to the copier/printer, or if the copier/printer is not powered 
on, a message displays indicating the status. Expect this message. The E-41 detects the 
copier/printer after you connect the E-41 to the copier/printer.

8. Reattach any dongle(s) (for example, for Compose or Impose) or USB storage device you may 

have removed previously.

Error messages

One of the following error messages may display on the E-41 Control Panel or monitor when 
you attempt to transfer options to the new motherboard. 

Could not mount the dos/boot partition

—

You have attempted to transfer options using the 

Feature Update CD. The Feature Update CD is not supported by the E-41. Obtain the 
Fiery Options Utility and try the procedure again. 

Invalid dongle found! Please remove dongle and connect the correct dongle

—

The 

attached dongle is not supported by the Fiery Options Utility. The dongle may have been 
attached by mistake. Obtain a valid dongle and try again.

More than one dongle found. Remove all dongles except the correct dongle

—

The 

Fiery Options Utility will not work when more than one dongle is attached to the system. 

No uses remaining

—

The dongle has already been used and cannot be reused. Obtain an 

unused dongle and start again.

Check power and Video cable connections

—

There is a problem with the connection 

between the E-41 and the copier/printer. Make sure that the interface cables are properly 
connected and the copier/printer is on and ready to print.

If an error condition cannot be corrected, restore the previous hardware configuration, if 
possible, and contact your authorized service/support center.

Summary of Contents for E-41


































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands