manualshive.com logo in svg

Fiery E-41, Installation And Service Manual

Share
Download
Fiery E-41 Installation And Service Manual Download Page 33

U

SING

 

THE

 E-41

33

Buttons

Activity light

The activity light on the E-41 Control Panel indicates current E-41 activity. If the light is:

Line selection 
buttons

Use the four line selection buttons on the right side of the Control 
Panel to select the command displayed on the corresponding line 
of the LCD display. 

Up and Down 
buttons

Use these buttons to scroll to different screens in multi-screen lists 
or prompts.

Menu button

Press this button to view the Eject CD/DVD, Restart Server, Shut 
Down System, and Reboot System options.

Flashing amber

The E-41 is starting up and the BIOS has established 
communication with the User Interface Board (UIB).

Flashing green

The E-41 is continuing startup and the Windows  operating 
system has established communication with the UIB.

Solid green

The E-41 is powered on and in the Idle state.

Solid amber

The E-41 is powered off, but the AC power cable is plugged into 
the power source. The Control Panel LCD continues to draw 
power when the E-41 is off. 

Flashing or

 

solid red

An error has caused printing to be disabled.

No light

The E-41 is powered off and the AC power cable is not connected 
to a power source.

Summary of Contents for E-41


































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands