Fiery E-41 Installation And Service Manual Download Page 68

Page: 68 / 161

ERVICE

ROCEDURES

REPLACE

BOARDS

CABLES

AND

COMPONENTS

1. Replace the HDD bracket, with HDD attached (see

page 95

You removed the HDD bracket to provide clearance for removing the motherboard.

2. Replace the following cables:

• CPU power cable (8-pin, PW1)

• Motherboard power cable (20-pin, PW2)

• UIB cable (J38; see detail below)

• HDD cables:

–

Power supply SATA cable to the back

of the HDD

–

SATA data cable to the HDD and motherboard
connector SATA 2

• DVD drive cables:

–

Power and data combination cable to the back of
the DVD drive

–

SATA data cable to motherboard connector
SATA 1

OTE

Connect the thin, black SATA power cable

connectors to the HDD and DVD drive. Do not connect
the white, 4-pin power cable connectors. Connecting
both types of power cables will damage the HDD and
DVD drive.

• Front panel USB port cables (J22 and J35; see detail)

• Speaker cable (J40; see detail)

Make sure that the small triangle on the cable
connector is aligned with pin 1 on J40.

• Power button cable (JP4 pins 6 and 8)

Make sure that the small triangle on the cable
connector is aligned with pin 8 on JP4.

• Reset button cable (JP4 pins 5 and 7; see detail)

Make sure that the small triangle on the cable
connector is aligned with pin 7 on JP4.

• Front panel fan cable (FAN 4)

DVD drive

(SATA 1)

HDD 1

(SATA 2)

HDD 2

(SATA 3;

FAN 4

J40

Speaker

Reset

Power

J22

Front panel USB port cables

J35

J38

JP4

UIB cable

dual-HDD
systems only)

(Orientation of
these ports may vary)

Summary of Contents for E-41


































































































































































Search results

Summary of Contents for E-41

Reviews:

Brands by name

Popular brands

Fiery E-41, Installation And Service Manual

Search results

Summary of Contents for E-41

Reviews:

Brands by name

Popular brands