6
7
OPERATING INSTRUCTIONS
STEP 2
Attach the handset using the included adhesive strip or using two M3 Phillips round head screws
• Position the handset on the left or right side of the table, according to user preference.
• Mount the handset flush to the front edge of the table. If using M3 attachment method, ensure handset is lined up to pre-drilled holes
on the desktop.
• Plug handset into controller on base.
• Plug power cable into controller on base and into an power outlet.
INITIALISE THE SYSTEM
WARNING:
Only light pressure required to operate handset. When lowering the table, apply light pressure to the center of the handset (Fellowes logo). Applying
too much pressure, pulling or pushing on the lower part of the handset may cause damage to the unit.
IMPORTANT:
The initialisation process below must be completed before operating the table. Throughout the initialisation operation, CAL is displayed and will
remain until procedure is complete.
CAUTION:
Ensure proper clearance. Make sure all objects are clear of the table
• Lightly touch the Fellowes logo and M buttons simultaneously for 10-15 seconds.
• The legs will begin to move down at half speed of normal operation.
• Continue to hold the buttons.
• The legs will move down to the lowest position, then rebound 2mm to 5mm (1/16" to 3/16“) and stop. This can take between 10-45 seconds
depending on the thickness of the table top.
• Release both buttons at the same time. This completes the initialisation procedure.
• If initialisation is started and not finished, the table will not operate. You must finish the initialisation process.
RESET THE SYSTEM TO FACTORY SETTINGS
To reset the handset to factory settings follow the same instructions as 'Initialise
the System'.
In case of error message or in the event of a power outage please reset the system.
GENERAL OPERATION
Move the table up or down by lightly holding your finger on the top or back of the
handset until the work surface reaches the desired height.
The table will continue to move up or down until you release the button or until the
maximum or minimum height is reached.
MEMORY STOP POSITIONS
There are two groups of memory settings, each with two height settings. To toggle
between the two users momentarily press the M button and display will read U1 or
U2. Up to four memory stop positions can be used to save specific heights of the work
surface. To set a specific position:
Raise or lower the table to the position you want to save.
Lightly touch the M button for two seconds, the LED display will blink. This means it has
stored the location. To clear storage settings, lightly touch the M button for 8 seconds
until CLR displays.
CHANGING THE HEIGHT DISPLAY UNITS
This function allows you to toggle the display units from inches to centimeters.
Lightly touch and hold up and down at same time for 10 seconds.
STEP 3
Level Feet
• If table feels unbalanced adjust the (4) leveling pads located on bottom of feet.
• Turn clockwise to lower and counterclockwise to raise.
Height
Display
Memory Set
Button
Raise/Lower
Raise
Lower
FELLOWES LEVADO™ HEIGHT ADJUSTABLE DESK BASE LIMITED WARRANTY
Fellowes, Inc. (the “Company”) warrants the Levado™ Height Adjustable Desk Base (“Product”) to be free from defects in material and workmanship for the time period as set forth below.
The structural frame for a period of fifteen (15) years from the date of original purchase of the product.
All electrical components for a period of seven (7) years from the date of original purchase of the product.
This warranty applies only to the initial purchaser and does not cover claims resulting from misuse, failure to follow instructions on installation and use, neglect, use of unauthorized attachments,
commercial use, use on a current or voltage other than specified on the product, or unauthorized service during the warranty period on conditions otherwise covered by warranty.
THE DURATION OF ANY IMPLIED WARRANTIES, INCLUDING BUT NOT LIMITED TO ANY IMPLIED WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE, IS EXPRESSLY
LIMITED TO THE DURATION OF THIS LIMITED WARRANTY.
UNLESS REQUIRED BY APPLICABLE LAW, THE CUSTOMER’S EXCLUSIVE REMEDY FOR BREACH OF THIS WARRANTY OR ANY IMPLIED WARRANTY OR OF ANY OTHER OBLIGATION ARISING BY
OPERATION OF LAW OR OTHERWISE SHALL BE LIMITED AS SPECIFIED HEREIN TO REPAIR, REPLACEMENT OR A REFUND OF THE PURCHASE PRICE, AT THE COMPANY’S SOLE OPTION.
UNDER NO CIRCUMSTANCE WILL THE COMPANY, ITS AFFILIATES, SUBSIDIARIES, RELATED ENTITIES, RESELLERS OR THEIR RESPECTIVE OFFICERS, DIRECTORS OR EMPLOYEES OR THOSE PERSONS FOR
WHOM THEY ARE BY LAW RESPONSIBLE, BE LIABLE FOR CONSEQUENTIAL OR INCIDENTAL DAMAGES SUSTAINED IN CONNECTION WITH THE PRODUCT. THE COMPANY AND THESE OTHER PARTIES
DO NOT ASSUME OR AUTHORIZE ANY REPRESENTATIVE OR OTHER PERSON TO ASSUME FOR ANY OF THEM ANY OBLIGATION OR LIABILITY OTHER THAN AS IS EXPRESSLY SET FORTH HEREIN.
The duration, terms and conditions of this warranty are valid worldwide, except where different limitations, restrictions or conditions may be required by local law.
Australia Residents Only:
Our goods come with guarantees that cannot be excluded under the Australian Consumer Law. You are entitled to a replacement or refund for a major failure and for compensation for any other
reasonably foreseeable loss or damage. You are also entitled to have the goods repaired or replaced if the goods fail to be of acceptable quality and the failure does not amount to a major
failure. The benefits under Fellowes’ Warranty are in addition to other rights and remedies under a law in relation to the product.
CAL
