manualshive.com logo in svg

Faulhaber MC 5004 P STO, Installation Instructions Manual

Share
Download
Faulhaber MC 5004 P STO Installation Instructions Manual Download Page 55

1st edition, 03-05-2018

7000.05063, 1st edition, 03-05-2018

7000.05063

Maintenance and diagnostics

55

5

Maintenance and diagnostics

5.1

Maintenance tasks

The drive is generally maintenance-free. Where the device is mounted in a cabinet, depend-
ing on the deposition of dust the air filter should be regularly checked and cleaned if neces-
sary.

5.2

Diagnostics

5.2.1

Standard PCB

Standard PCB

Fig. 38: Isometric (left) and front view (right) of the standard PCB

Tab. 33: Device status LEDs

Designation

Function

Status LED

Green (continuous): Device active.

Green (flashing): Device active. However the state machine has not yet reached the 

Operation 

Enabled

 state.

Red (continuously flashing): The drive has switched to a fault state. The output stage will be 

switched off or has already been switched off.

Red (Error code): Boot procedure failed. Please contact FAULHABER Support.

Power LED

Green: Power supply within the permissible range.

Off: Power supply not within the permissible range.

Status LED

Power LED

STO Status LED

No-Error LED

Summary of Contents for MC 5004 P STO






































































Reviews:

No comments

Brands by name

Popular brands

Load more brands