manualshive.com logo in svg

Faulhaber MC 5004 P STO, Installation Instructions Manual

Share
Download
Faulhaber MC 5004 P STO Installation Instructions Manual Download Page 12

1st edition, 03-05-2018

7000.05063, 1st edition, 03-05-2018

7000.05063

Safety

12

2.5

EC directives on product safety

The following EC directives and standards on product safety must be observed.

If the Motion Controller is being used outside the EU, international, national and 
regional directives must be also observed.

Machinery Directive (2006/42/EC)
The products described in these installation instructions are electrical components with 
integrated safety function according to the Machinery Directive. They are therefore to be 
considered incomplete machines according to the Machinery Directive. Compliance is docu-
mented by the Declaration of Incorporation for the product and by the EC Declaration of 
the Conformity for the safety function.

Low Voltage Directive (2014/35/EU)
The Low Voltage Directive applies for all electrical equipment with a nominal voltage of 75 
to 1500 V DC and 50 to 1000 V AC. The products described in these installation instructions 
do not fall within the scope of this directive, since they are intended for lower voltages.

EMC Directive (2014/30/EU)
The directive concerning electromagnetic compatibility (EMC) applies to all electrical and 
electronic devices, installations and systems sold to an end user. In addition, CE marking can 
be undertaken for built-in components according to the EMC Directive. Conformity with 
the directive is documented in the Declaration of Conformity.

RoHS Directive (2011/65/EU)
The directive restricts the use of certain hazardous materials in electrical and electronic 
devices. The products described in these installation instructions fall within the scope of this 
directive. Conformity with the directive is documented in the EC Declaration of Conformity.

WEEE Directive (2012/19/EU)
The directive on the disposal of electrical and electronic devices prescribes the separate col-
lection of old electrical and electronic devices. The products described in these installation 
instructions fall within the scope of this directive.

Applied standards
Various harmonised standards were applied to the products described in these installation 
instructions; these standards are documented in the EC Declaration of Conformity.

You can find the Declaration of Incorporation for the product and the EC Declaration of 
Conformity for the safety function in chap. 8.2, p. 62 and chap. 8.3, p. 63.

Summary of Contents for MC 5004 P STO






































































Reviews:

No comments

Brands by name

Popular brands

Load more brands