FarmTek Growers Supply HydroCycle 11291950 Manual Download Page 9

Page: 9 / 41

Revision date: 09.20.21

11291950

1. Place one 10' channel (117077L120) on a bench or saw

horses.

2. Using the 112509 adhesive, attach a plain end cap (no

outlet–117078) to one end and a end cap with an outlet

(117079) to the other end. Coat the ends of the channel with

adhesive

before

you install the end caps.

3. Repeat the process for all channels. Set channels aside to

allow the adhesive to dry.

4. Next, attach a 90° elbow (WF6682) to each 117079 end

cap as shown. Apply pvc primer and pvc cement to end cap

outlet and inside of fitting. Slide fitting onto outlet. Install

fitting as shown with open end pointing down in the 6:00

o'clock position.

ATTENTION:

Verify that you are using the WF6682 elbows

that do not have threads.

Do not use the WF6692 elbow.

5. Once all end caps and drain elbows are in place, carefully

flip all channels over so the bottom is facing up and the open

top is down.

6. Apply the 112509 adhesive along the edges to secure end

caps to each 10' channel. Photos show an end cap with an

outlet. Secure the plain end caps in the same manner.

ASSEMBLE 117077L120 CHANNELS (10')

NOTE:

Be sure to coat all edges and seams of the end caps

to prevent leaks.

7. Allow the adhesive to dry before moving the channels or

testing the system.

8. Continue by installing the 2" hangers.

Apply pvc primer and pvc cement in a well-ventilated area.

Read container information for additional precautions.

WF6682

Elbow

PVC Primer

and PVC

Cement

NFT Channel (10')

WF6682

Elbow

open

top-inside

channel

bottom

Assemble 10' Channels

Summary of Contents for Growers Supply HydroCycle 11291950










































Search results

Summary of Contents for Growers Supply HydroCycle 11291950

Reviews:

Related manuals for Growers Supply HydroCycle 11291950

Brands by name

Popular brands

FarmTek Growers Supply HydroCycle 11291950, Manual

Search results

Summary of Contents for Growers Supply HydroCycle 11291950

Reviews:

Related manuals for Growers Supply HydroCycle 11291950

Brands by name

Popular brands