FarmTek Growers Supply HydroCycle 11291950 Manual Download Page 5

Page: 5 / 41

Revision date: 09.20.21

11291950

Assemble Frame

ASSEMBLE SIDE FRAMES

Assemble frame on a flat, level surface for best results.

Complete these steps:
1. Review the frame diagram at the right (and at the back

of this guide) and gather two (2) corner tubes and four

(4) longer, side frame tubes to construct one side frame

assembly.

2. Position the two (2) corner tubes so holes match up. The

hole closest to the top end of each corner pipe is used to

attach the upper side tube. Lower tier is approximately 23"

from the end or bottom of the pipe. See diagram.

3. Take four (4) of the longer, side tubes and connect these

to the corner tubes using the 112772 flat head bolts to

assemble the first side frame.

4. With assistance, set the assembly aside and repeat the

steps to assemble the remaining side frame.

5. Once both identical side frames are assembled, position

these opposite each other. See diagram below.

6. Continue by installing the adjustable feet – Procedure 2.

Top view showing two assembled side frames.

112772

5/16" x 3" Flat

Head Bolt

Assembled Side Frame

Upper T

ier

Lower T

ier

115" Side Tube

FD15LMGL11500S2

80" Corner Tube

FD15VMGL08000S4

23"

ATTENTION:

The vertical tubes include holes

of two different diameters. Install the larger

hole to the outside to allow the flat head bolt to

sit flush with the tube surface when installed.

112772

Large hole

to this side.

Summary of Contents for Growers Supply HydroCycle 11291950










































Search results

Summary of Contents for Growers Supply HydroCycle 11291950

Reviews:

Related manuals for Growers Supply HydroCycle 11291950

Brands by name

Popular brands

FarmTek Growers Supply HydroCycle 11291950, Manual

Search results

Summary of Contents for Growers Supply HydroCycle 11291950

Reviews:

Related manuals for Growers Supply HydroCycle 11291950

Brands by name

Popular brands