FarmTek Growers Supply HydroCycle 11291950 Manual Download Page 30 | Manualshive

Page: 30 / 41

background image

30

11291950

Revision date: 09.20.21

Clean the reservoir periodically to maximize plant growth and to minimize system contamination. The steps that follow can be used to change nutrient solution

and to pump the reservoir for cleaning and typical maintenance.

Cleaning the filter is strongly recommended after cleaning the reservoir.

RESERVOIR CLEANING AND MAINTENANCE

1. Turn off the nutrient pump and connect a

garden hose to the shutoff valve of the filter.

Place the end of the hose in a bucket or run it

to the desired location.

2. Open the shutoff valve on the filter and turn the

pump on to pump out the reservoir. Turn off the

pump once the reservoir is empty.

3. Clean reservoir. Repeat steps to pump it out if

needed.

4. Close the shutoff valve.

5. Remove the hose and clean the filter. See

previous page for filter cleaning procedure.

6. Refill the reservoir with nutrient solution. Turn

on the pump to resume operation. Check all

fittings, tubes, and filter for leaks.

Shutoff

Valve

Operational and Maintenance Information

«
...
28
29
30
31
32
...
»

Summary of Contents for Growers Supply HydroCycle 11291950










































Reviews:

No comments

Related manuals for Growers Supply HydroCycle 11291950

Brand: F&V Pages: 5

Brand: Qiagen Pages: 48

Brand: Qiagen Pages: 162

Brand: Qazqa Pages: 4

Brand: Qlightec Pages: 12

Brand: U Technology Pages: 6

Brand: Bartscher Pages: 61

ABS-Lock III-BE

Brand: ABS Pages: 8

Brand: X-METAL Pages: 135

Brand: Ugin Pages: 39

Brand: Grange Pages: 2

Dual-Lite EVHC-BC Series

Brand: Hubbell Pages: 2

AtLite Sure-Lites SELDWA29SD

Brand: Eaton Pages: 4

Brand: Xils lab Pages: 31

Brand: Dentsply Sirona Pages: 2

Brand: Claas Pages: 252

Brand: M-system Pages: 5

Brand: American DJ Pages: 4

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands