FarmTek Growers Supply HydroCycle 11291950 Manual Download Page 6

Page: 6 / 41

11291950

Revision date: 09.20.21

STEP 4

Side Frame Assembly

with Adjustable Feet

Center

ASSEMBLE FRAME—INSTALL ADJUSTABLE FEET

Assemble frame on a flat, level surface for best results.

2. Slide one 112477 insert assembly into the bottom of each 80"

vertical leg tube. Tap gently with a small hammer if needed to seat.

3. Secure each insert to each tube using two (2) 112838 Tek screws.

Install screws through leg tube and wall of the 112477 insert.

Install screws to the left or right of the centerline of the leg tube

to prevent hitting the threaded shaft of the adjustable foot.

4. Adjust the 113030S01 foot so that it is seated against the threaded

plate of the insert and nut. See diagram.

5. Continue with the main frame assembly – Procedure 3.

Complete these steps:
1. Add one FALB34B nut to the threaded stud of each 113030S01 foot and attach one foot to each 112477 insert.

Assemble Frame

112477

FALB34B

Bottom

of Leg

Tube

112477

FALB34B

Locknut

113030S01

112838

Tek Screw

100442

Summary of Contents for Growers Supply HydroCycle 11291950










































Search results

Summary of Contents for Growers Supply HydroCycle 11291950

Reviews:

Related manuals for Growers Supply HydroCycle 11291950

Brands by name

Popular brands

FarmTek Growers Supply HydroCycle 11291950, Manual

Search results

Summary of Contents for Growers Supply HydroCycle 11291950

Reviews:

Related manuals for Growers Supply HydroCycle 11291950

Brands by name

Popular brands