![background image](http://html1.mh-extra.com/html/eaton/cooper-lightig-all-pro-wl2540lp/cooper-lightig-all-pro-wl2540lp_instruction-manual_3854310001.webp)
1
Questions?/ Des questions?/ ¿Preguntas? 1-800-334-6871 [email protected]
Instruction Manual / Manuel d’instructions/ Instrucciones
PACKAGING CONTENTS/CONTENIDO DEL PAQUETE/CONTENIDO DEL PAQUETE
ITEMS REQUIRED
(Purchase separately)
• Adjustable Wrench
WARNINGS AND CAUTIONS
• Heed all warnings, including below warnings AND those included on product.
• Save these instructions and warnings.
• For indoor and outdoor use.
• cULus LISTED for wet location.
• Your LED fixture is prewired. No replacement bulb necessary. Disassembling your fixture
will void the warranty.
• Connect fixture to a 120 volt, 60 Hz power source. Any other connection voids the warranty.
• Do not look directly at lighted lamp.
• Read and follow these instructions.
WARNING
• Risk of fire/electric shock.
• The electrical system, and the method of electrically connecting the fixture to it, must be in
accordance with the National Electrical Code and local building codes.
WARNING:
When using outdoor use portable luminaires, basic safety precautions should
always be followed to reduce the risk of fire, electric shock, and personal injury, including
the following:
Read All INSTRUCTIONS.
• Use only three-wire outdoor extension cords that have three-prong grounding plugs and
grounding recptacles that accept the appliance’s plug.
• Ground Fault Circuit Interrupter (GFCI) protection is to be provided on the circuit(s) outlet(s)
to be used for the wet location portable luminaire. Receptacles are available having built-in
GFCI protection and are able to be used for this measure of safety.
• Use only with an extrension cord for outdoor use, such as an extension cord of cord type
SW, SW-A, SOW, SOW-A, STW, STW-A, STOW, STOW-A, SJW, SJW-A, SJOW, SJOW-A, SJTW,
SJTW-A, SJTOW, SJTOW-A.
• Max distance to receptacle is 3 feet.
• This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reason
able protection against harmful interference in a residential installation. This equipment
generates, uses and can radiate radio frequency energy and if not installed and used in
accordance with the instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation. If
this equipment does cause harmful interference to radio or television reception, which can be
determined by turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
WL2540LP
A.
LED Worklight
Luminaria LED para sitios de trabajo
Lampe de travail à DEL
ENGLISH
B.
Stand
Pie de base
Support
C.
(2) M6 Lock Washers
Arandelas de seguridad M6 (x 2)
(2) rondelles freins M6
D.
(2) M6 x 24mm Screws
Tornillos M6 x 24 mm (x 2)
(2) vis M6 de 24 mm
WARNING: FCC Regulations state that any unauthorized changes or
modifications to this equipment not expressly approved by the manufacturer
could void the user’s authorization to operate this equipment.
SAVE THESE INSTRUCTIONS.
INSTALLING YOUR FIXTURE
WARNING:
Deviation from the assembly instructions
may result in a risk of fire or electric shock.
1. Using adjustable wrench (not included) attach
worklight (A) with bracket to worklight stand (B)
using QTY 2 M6 x 24MM screws (D) and QTY 2 M6
lock washers (C) as in (FIG 1).
AIMING THE LIGHT
1. To aim fixture loosen two knob handles on the
side of the worklight (FIG 2). Tilt worklight to
desired position and tighten knobs. Worklight can
angle 10° degrees down or 90° up (FIG 3). When
tilting worklight 90° up, pass power cord through
hole between stand and worklight to prevent
wearing power cord (FIG 4).
2
1
3
4
C
D
A
B