Home
/
FarmTek
/
FodderPro 2.0 Full Feed System-Wall Mount...
/
Manual

FarmTek FodderPro 2.0 Full Feed System-Wall Mount..., Manual

Share

Page: 38 / 53

background image

38

38

111628W

Revision date: 09.25.18

INSTALL THE SUPPLY MANIFOLD — continued

4

3. Next, locate the supply tubes with micro valves. There are two different lengths for this

fodder system–112305 (18") & 112306 (28").

4. Install two (1) short tube (112305) and one (1) long tube (112306) at each level. See the

diagrams below.

ATTENTION: FITTINGS ON MANIFOLD CAN BREAK! DO NOT FORCE THE TUBES

ONTO THE MANIFOLD FITTINGS! WET THE END OF EACH TUBE BEFORE

INSTALLATION AND GENTLY SLIDE IT EVENLY OVER THE FITTING.

Wet the end

of the supply

tube.

Gently slide

it onto the

fitting.

Repeat for

all remaining

supply tubes.

Assembly Instructions

W

ALL

112305

112306

W

ALL

System shown differs from the actual system.

Installation of the supply tubes is the same.

«
...
36
37
38
39
40
...
»

Summary of Contents for FodderPro 2.0 Full Feed System-Wall Mount...






















































Reviews:

No comments

Related manuals for FodderPro 2.0 Full Feed System-Wall Mount...

Brand: TC Electronic Pages: 2

Brand: Bahco Pages: 131

Brand: Bahco Pages: 126

Brand: Keithley Pages: 79

Brand: Toro Pages: 12

Brand: Beckman Coulter Pages: 52

Brand: E2S Pages: 8

Brand: JEOL Pages: 4

Brand: Milwaukee Pages: 2

AccuTrak VPE-2000

Brand: Superior Signal Pages: 22

Brand: GLITCHMACHINES Pages: 8

Brand: UCHIDA Pages: 17

Brand: Zipper Mowers Pages: 50

Brand: Amerelle Pages: 4

Brand: TATU Pages: 84

THE FLASH JUKE 12

Brand: N-Gear Pages: 28

Brand: BiOptic Pages: 46

Brand: Omegawave Pages: 47

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands