8.4
TIME LEARNING
go to
“8.5 ADVANCED PROGRAMMING”
8.3
INPUT ASSIGNING
Card 460P and the input expansion module (MEI module) have a default terminal block input alloca-
tion, which is the one given in the electronic control unit instructions.
However, with the exception of input 1 of the 460P (which represents the OPEN-A input and cannot be
changed), a different meaning can be assigned to the other available inputs in accordance with the
rules and limitations given in chapter 12 “Input management” in this manual.
Time learning serves to determine the working and deceleration times of each leaf.
As the motors are activated during this phase, it is advisable to check beforehand that the automation
works correctly (by running the “motor test” under the Diagnostics menu) and calibrate the by-pass
valves.
You can quit the learning cycle at any time (with consequent loss of the acquired times) by pressing the
ESC key, which takes you back to the beginning of the cycle.
N.B.:
1) The time learning cycle is displayed only if the FAACTOTUM is connected to the 460P control unit.
2) The “DECELERATE” option in the cycle menus appears only if Gatecoder is used, or if deceleration by
time is used.
3) When the limit switches are used, the “DECELERATE” option does not appear because the decelera-
tion start point is determined by the opening of the limit switch contact.
4)
In the case of swing gates, the mechanical opening and closure stops are always necessary for
correct operation of the automation (even when the Gatecoder is used).
5) Leaf 1 is the leaf connected to motor M1; Leaf 2 is the leaf connected to motor M2.
8
ENTER
➲
This menu appears only if “NUMBER OF OPERATORS = 2” has previously been set.
When the
ñ
key is pressed, leaf 2 starts to close; when it is pressed again the leaf
stops closing and so on.
Each time the key is pressed, the arrow on the display moves to select the effect of
the subsequent pulse.
Close Leaf 2 completely and press ENTER.
(cont.)
ASSOCIATE CHOSEN
FUNCTION WITH INPUT
AND PRESS ENTER
INP. 2 = XXXXXX
ENTER
INPUT MODULE?
1->YES
2 NO
1
F1
2
F2
C
à
When the
ñ
key is pressed, leaf 1 starts to close; when it is pressed again the leaf
stops closing and so on.
Each time the key is pressed, the arrow on the display moves to select the effect
of the subsequent pulse.
Close Leaf 1 completely and press ENTER.
ENTER
(cont.)
TIME LEARNING?
1->YES
2 NO
2
F2
1
F1
ENTER
CLOSE LEAF 1
ñ
CLOSE
STOP
PRESS ENTER TO CONT.
CLOSE LEAF 2
ñ
CLOSE
STOP
PRESS ENTER TO CONT.
ENTER
The currently attributed function is shown for each available input (except for
inputs IN1 on the 460P and IN10-11 on the MEI module):
Press ENTER to confirm.
To modify, use
ñ
and
ò
to select the function you wish to assign to the input and
press ENTER.
Pressing the CLEAR key shows the input’s default function.
The input can also be disabled by selecting the “INACT” function.
All the inputs must be set in order to proceed to the subsequent menu.
When confirming each configured safety input (FSW-OP/CL, SAFE OP/CL), a menu
allows the Failsafe to be enabled or disabled.
➲
Do not assign the same function to more than one inputs.
To skip the allocation cycle (and confirm the current settings), hold down the
SHIFT key and press the
ò
key.
PG
PG
ENTER
CLEAR
SHIFT
Check whether the Input Expansion Module (MEI module) is installed in the 460P
card and select the corresponding option:
1 = MEI module installed
2 = MEI module not installed
Make the selection by moving the arrow-shaped cursor alongside the desired
option using the
ï
and
ð
keys and pressing ENTER, or key in the corresponding
number directly.
1
F1
2
F2
or
ENTER
+
Select option:
1 = Perform time learning cycle
2 = Do not perform time learning cycle and go to “Advanced programming”
1
F1
2
F2
or
ENTER
+
Make the selection by moving the arrow-shaped cursor alongside the desired
option using the
ï
and
ð
keys and pressing ENTER, or key in the corresponding
number directly.
