FAAC FAACTOTUM, Manual, Page: 19 / 22

14.1 PRE-FLASHING
Pre-flashing is a function which, with the automation stopped
and the flashing light off, allows the flashing light to come on a
few seconds before movement begins. Programmable types of
pre-flashing:
1) Opening pre-flashing 1
The flashing light is powered for the set time before switching
from the closed/locked state to the opening state.
2) Closure pre-flashing 1
The flashing light is powered for the set time before switching
from the open/open on pause/stopped state to the closure state.
3) Pre-flashing at end of pause
The flashing light is powered for the set time at the end of the
pause before starting the movement.
14.2 FLASHING LIGHT ON DURING PAUSE
The flashing light is powered for the entire duration of the pause.
REG. No. VALUE FUNCTION DEFAULT
45 seconds opening pre-flashing time 0
REG. No. VALUE FUNCTION DEFAULT
14 * XXXXXX1X pre-flashing at end of pause
XXXXXX0X
REG. No. VALUE FUNCTION DEFAULT
14 * XXXXX1XX flashing light on during pause
XXXXX0XX
14.3 WARNING LIGHT ON DURING CLOSURE
Sets the warning light to stay on even during closure: the only
state in which it is off is automation closed.
Default: opening pre-flashing disabled (0 seconds)
Default: closing pre-flashing disabled (0 seconds)
Default: pre-flashing at end of pause disabled
Default: flashing light off during pause
14.4 WARNING LIGHT OUTPUT OPERATION
Allows the 460P warning light output (N.O. contact) to be used for
other functions:
1) Timed courtesy light contact
The warning light output N.O. contact closes for a settable time
(Reg.79) during each opening, closure, photocell operation and
pause start of the automation.
Every state which causes the contact to close resets and restarts
the timing count.
REG. No. VALUE FUNCTION DEFAULT
14 * 0100XXXX warning light on during closure
0000XXXX
Default: standard operation of the warning lamp is:
automation closed =
warning light off
automation closing = warning light flashing
all other states = warning light on
2) Panic state active contact
The warning light output N.O. contact closes when the panic
state is activated in the electronic control unit 460P following the
“EMERG” command.
The contact remains closed until the state is reset.
REG. No. VALUE FUNCTION DEFAULT
14 * 1001XXXX panic state activated
0000XXXX
Default: standard warning light function
3) Automation open state contact
The warning light output N.O. contact closes for the entire time
the automation remains in the open or the open on pause states.
REG. No. VALUE FUNCTION DEFAULT
14 * 1010XXXX automation open/pause state
0000XXXX
Default: standard warning light function
4) Automation opening state contact
The warning light output N.O. contact closes for the entire time
the automation remains in the opening state.
REG. No. VALUE FUNCTION DEFAULT
14 * 1011XXXX automation opening state
0000XXXX
Default: standard warning light function
5) Automation closure state contact
The warning light output N.O. contact closes for the entire time
the automation remains in the closure state.
REG. No. VALUE FUNCTION DEFAULT
14 * 1100XXXX automation closure state
0000XXXX
Default: standard warning light function
6) Stop impulse active contact
The warning light output N.O. contact closes for the entire time
the stop button is pressed.
REG. No. VALUE FUNCTION DEFAULT
14 * 1101XXXX stop button pressed
0000XXXX
Default: standard warning light function
7) Automation pause state contact
The warning light output N.O. contact closes for the entire time
the automation remains in the pause state.
REG. No. VALUE FUNCTION DEFAULT
14 * 1110XXXX automation in pause state
0000XXXX
Default: standard warning light function
8) Automation closed state contact
The warning light output N.O. contact closes for the entire time
the automation remains in the closed state.
REG. No. VALUE FUNCTION DEFAULT
14 * 1111XXXX automation closed state
0000XXXX
Default: standard warning light function
REG. No. VALUE FUNCTION DEFAULT
46
seconds closure pre-flashing time 0
14. EXAMPLES OF REGISTER SETTINGS
The following are some examples of register settings for the most
useful functions, complete with explanations.
➲
The registers marked with an asterisk (*) are “Logic registers”
(see chapter 13).
REG. No. VALUE FUNCTION DEFAULT
79 seconds contact closure time
100
Default: 100 seconds
17
REG. No. VALUE FUNCTION DEFAULT
14 * 1000XXXX timed courtesy contact
0000XXXX
Default: standard warning light function
REG. No. VALUE FUNCTION DEFAULT
48 seconds
pre-flashing time at end of pause
0
Default: 0 seconds