background image

 

A

A

CCESSORY

CCESSORY

 

 

C

C

ONNECTIONS

ONNECTIONS

 

 

A

CCESS

 C

ONTROL

 C

ONNECTION

Access Control Devices such as Telephone Entry Systems, Digital Locks and Card Readers may be connected to the Access 
Input to control the gate operator.  When an Access Device is active, the Access LED will light. 
 

 
 
 
 
 
 
 

 
 
 
 

 
 

F

IRE

 L

OCK

 C

ONNECTION

Fire Lock Controls such as Knox Locks and Fire Boxes may be connected to the Fire Input to control the gate operator.  When 
a Fire Lock Control is active, the Fire LED will light. 
 

Fire Input: 

1.  Allows Fire Lock Controls to activate the gate. 

2.  This input knows the position of the gate and will only open the 

gate when activated. 

3.  If Close Time Delay is ON, gate will open and remain open until 

the fire control relay is released.  Then the gate will time out and 
close. 

4.  If Close Time Delay is OFF and the gate is in closed position, 

gate will open and remain open until an external input of any 
sort closes the gate. 

5.  If Close Time Delay is OFF and gate is in open position, gate 

will remain open until an external input is made.  This prevents 
the Fire Input from closing the gate if in the open position. 

  
Connecting Access Devices: 

1.  Connect Fire Lock Control relays to FIRE and COMMON.  

(Most devices use Normally Closed & Common) 

 
 
 
 
 
 
 

 
 
 
 
 
 
NOTE:  Consult your local Fire Department for proper 
building codes and Fire Lock requirements. 

FIRE 

LOCK 

Access Input: 

1.  Allows external Access Control Devices to activate the gate. 

2.  If Close Time Delay is ON, gate will open and remain open until 

the access device relay is released.  Then the gate will time out 
and close. 

3.  If Close Time Delay is OFF and the gate is in closed or open 

position, gate will travel in the opposite direction. 

4.  If Close Time Delay is OFF and the gate is in mid cycle, the 

gate will stop.  The direction will not be changed until another 
valid input is made.  

 
Connecting Access Devices: 

1.  Connect Access Control Device relays to ACCESS and 

COMMON.  (Most devices use Normally Open & Common) 

1  2 

4  5 

7  8 

Card Access 

Phone Entry 

DO NOT allow children to play near, on or with 

the gate, gate operator, or any of its controls. 

DSW2000 Swing Gate Operator 

21 

Summary of Contents for DSW2000




























Reviews: