background image

 

I

I

MPORTANT

MPORTANT

 

 

S

S

AFETY

AFETY

 

 

I

I

NFORMATION

NFORMATION

 

 

 

 

 

UL325 G

ATE

 O

PERATOR

 C

LASSIFICATION

RESIDENITAL VEHICULAR GATE OPERATOR 
CLASS I:  A vehicular gate operator (or system) intended for use in a home of one 
to four single family dwelling, or a garage or parking area associated therewith. 
 
 
 
COMMERCIAL/GENERAL ACCESS VEHICULAR GATE OPERATOR 
CLASS II:  A vehicular gate operator (or system) intended for use in a commercial 
location or building such as a multi-family housing unit (five or more single family 
units), hotels, garages, retail store, or other building servicing the general public. 
 
 
 
 
INDUSTRIAL/LIMITED ACCESS VEHICULAR GATE OPERATOR 
CLASS III:  A vehicular gate operator (or system) intended for use in an industrial 
location or building such as a factory or lading dock area or other locations not 
intended to service the general public. 
 
 
 
RESTRICTED ACCESS VEHICULAR GATE OPERATOR 
CLASS IV:  A vehicular gate operator (or system) intended for use in a guarded 
industrial location or building such as an airport security area or other restricted 
access locations not servicing the general public, in which unauthorized access is 
prevented via supervision by security personnel. 
 
 

G

LOSSARY

 O

F

 T

ERMS

GATE:  A moving barrier such as a swinging, sliding, raising, lowering, or the like, barrier, that is a stand-alone passage barrier 
or is that portion of a wall or fence system that controls entrance and/or egress by people or vehicles and completes the 
perimeter of a defined area. 
 
VEHICULAR SWING GATE OPERATOR (Or System):  A vehicular gate operator (or system) that controls a gate which 
swings and is intended for use for vehicular entrance or exit to a drive, parking lot, or the like. 
 
VEHICULAR HORIZONTAL SLIDE GATE OPERATOR (Or System):  A vehicular gate operator (or system) that controls a 
gate which slides in a horizontal direction that is intended for use for vehicular entrance or exit to a drive, parking lot, or the 
like. 
 
ENTRAPMENT:  A condition when a object is caught or held in a position that increases the risk of injury or death. 
 
INHERENT ENTRAPMENT SENSING DEVICE:  An automatic sensor system, which senses entrapment of a solid object and 
is incorporated as a permanent and integral part of the gate operator. 
 
NON-CONTACT SENSOR:  External device such as a photoelectric cell used to provide entrapment prevention and located 
where a risk of entrapment or obstruction exists. 
 
CONTACT SENSOR:  External device such as a edge sensor used to provide entrapment prevention located where a risk of 
entrapment or obstruction exists such as the leading edge, trailing edge, and posts mounted inside and outside of the vehicular 
slide gate and motor. 
 
 

IMPORTANT:  Make sure the gate operator usage classification is correct for the site 

and the type of gate.  Do not install this device beyond its classification. 

ABC Apartments 

ABC Manufacturing 

Regional Airport 

DSW2000 Swing Gate Operator 

Summary of Contents for DSW2000




























Reviews: