Chamberlain 8587W Manual Download

Page: 1 / 25

Wi-Fi

Garage Door Opener

Chain Drive Models 8587W and 8587WL

• Please read this manual and the safety materials

carefully!

• The door WILL NOT CLOSE unless the Protector

System

is connected and properly aligned.

• Periodic checks of the garage door opener are

required to ensure safe operation.

• This garage door opener is ONLY compatible with

MyQ

and S 2.0

accessories.

• DO NOT install on a one-piece door if using devices

or features providing unattended close. Unattended
devices and features are to be used ONLY with
sectional doors.

• Attach warning labels to the location indicated on

label.

FOR RESIDENTIAL USE ONLY

LiftMaster
300 Windsor Drive
Oak Brook, IL 60523

Register your garage door opener to receive

updates and offers from LiftMaster

Send it in

by texting

the photo to 71403 (US)

or visit

www.liftmaster.photo (Global)

Take a photo

of the camera icon

including the points ( ).

Summary of Contents for 8587W


























Search results

Summary of Contents for 8587W

Reviews:

Related manuals for 8587W

Brands by name

Popular brands

Chamberlain 8587W, Manual

Search results

Summary of Contents for 8587W

Reviews:

Related manuals for 8587W

Brands by name

Popular brands