Chamberlain Liftmaster Elite LA500 Installation Manual Download

Page: 1 / 60

LA500PKGU

Single Arm Package

LA500DC

Primary 24 VDC Actuator Arm for single
swing gate applications

LA500DCS

Secondary 24 VDC Actuator Arm for dual
swing gate applications

LIGHT COMMERCIAL - RESIDENTIAL DC

VEHICULAR SWING GATE OPERATOR

Model

LA500

INSTALLATION MANUAL

LiftMaster
845 Larch Avenue
Elmhurst, IL 60126-1196

•

THIS PRODUCT IS TO BE INSTALLED AND SERVICED BY A TRAINED GATE SYSTEMS TECHNICIAN ONLY.

•

This model is for use on vehicular passage gates ONLY and not intended for use on pedestrian passage gates.

•

This model is intended for use in Class I, II, III and IV vehicular swing gate applications.

•

Visit LiftMaster.com to locate a professional installing dealer in your area.

•

This gate operator is compatible with MyQ

and S 2.0

accessories.

Summary of Contents for Liftmaster Elite LA500




























































Search results

Summary of Contents for Liftmaster Elite LA500

Reviews:

Related manuals for Liftmaster Elite LA500

Brands by name

Popular brands

Chamberlain Liftmaster Elite LA500, Installation Manual

Search results

Summary of Contents for Liftmaster Elite LA500

Reviews:

Related manuals for Liftmaster Elite LA500

Brands by name

Popular brands