background image

B614 

732998 - Rev.A

Tr

ansla

tion of the orig

inal instruc

tions

ENGLISH

2.  SAFETY RECOMMENDATIONS

2.1  INSTALLER SAFETY

Installation activities require special work conditions 

to reduce to the minimum the risks of accidents and 

serious damage.  Furthermore, the suitable precau-

tions must be taken to prevent risks of injury to persons 

or damage.

 

!

The installer must be in good physical and mental 

condition, aware of and responsible for the hazards 

that may be generated when using the product.

The work area must be kept tidy and must not be 

left unattended.

Do not wear clothes or accessories (scarves, bracelets, 

etc.) that may get caught in moving parts.

Always wear the personal protective equipment rec-

ommended for the type of activity to be carried out.

The required level of workplace lighting must be equal 

to at least 200 lux.

Operate CE marked machinery and equipment in com-

pliance with the manufacturer's instructions.  Use 

work instruments in good conditions.

Use the transport and lifting equipment recom-

mended in the instructions manual.

Use safety-compliant portable ladders of adequate 

size, fitted with anti-slip devices at the top and bot-

tom, equipped with retainer hooks.

This product is placed onto the market as “partly 

completed machinery”, therefore it cannot be com-

missioned until the machine in which it will be incor-

porated has been identified and declared to conform 

to the Machinery Directive 2006/42/EC by the actual 

Manufacturer.

 

!

Incorrect installation and/or incorrect use of the 

product might cause serious harm to people.  Read 

and comply with all the instructions before starting 

any activity on the product.  Keep these instructions 

for future reference.

Perform installation and other activities adhering to 

the sequences provided in the instructions manual.

Always comply with all the requirements contained in 

the instructions and warning tables at the beginning 

of the paragraphs.  Always comply with the safety 

recommendations.

Only the installer and/or maintenance technician 

is authorised to work on the automation compo-

nents.  Do not modify the original components 

in any way.

Close off the work site (even temporarily) and prevent 

access/transit.  EC countries must comply with the 

legislation that transposes the European Construction 

Site Directive 92/57/EC.

The installer is responsible for the installation/testing 

of the automation and for completing the Register of 

the system.

The installer must prove or declare to possess technical 

and professional proficiency to perform installation, 

testing and maintenance activities according to the 

requirements in these instructions.

Summary of Contents for B614





































































Reviews: