4 6
B614 45
732998 - Rev.A
Tr
ansla
tion of the orig
inal instruc
tions
ENGLISH
9.3 XF RADIO MODULE
The E614 is fitted with an OMNIDEC integrated two
channel decoding system that can memorise, via the
XF radio module, FAAC radio controls that use the
following types of radio code: SLH/SLH LR, LC/RC, DS.
L
i
The three types of radio codes can coexist simulta-
neously.
A maximum of 256 codes can be memorised.
The codes memorised act as an OPEN or CLOSE
command.
The radio controls and the XF radio module must have
the same frequency.
When memorising the codes, keep the radio control
approximately one meter from the XF radio module.
1. (
) Insert the XF radio module in the connec-
tor J3 paying attention to the insertion direction.
2. Memorise the radio controls.
!
Ensure that there are no obstacles (persons or things)
while the automation is moving.
SLH/SLH LR - MEMORISING THE FIRST RADIO
CONTROL
1. Press and keep pressed the + key (OPEN program-
ming) or - (CLOSE programming). After pressing
the button for about 5 seconds, the corresponding
radio LED (DL4 or DL5) will start to flash to indicate
that the radio code learning phase has started.
2. Release the button. From this moment E614
stays in the learning phase for around 20 secs.
3. Press and hold down buttons P1 and P2 simulta-
neously on the SLH/SLH LR radio control (master
version only). The LED on the radio control starts
to flash.
4. Release both buttons; the LED on the radio control
continues to flash.
5. Make sure that the LED DL4 or DL5 on the board is
still flashing and press the button of the radio con-
trol that you wish to memorise for a few seconds
(the LED becomes steady). Release the button of
the radio control.
6. Press the same button that was used in the
previous step twice in succession to complete
the memorisation process. If the procedure
was carried out correctly, the B614 will open the
beam, if permitted by the operating mode that
has been set.
SLH/SLH LR - MEMORISING OTHER RADIO
CONTROLS
1. Press and hold down buttons P1 and P2 simul-
taneously on the SLH/SLH LR radio control that
has already been memorised (master version
only). The LED on the radio control starts to flash.
2. Release both buttons; the LED on the radio control
continues to flash.
3. Press and hold down the button that has already
been memorised (the LED becomes steady).
4. Place the remote control that has already been
memorised close to the remote control to be
memorised (keeping the button in the previous
step pressed).
5. Press the button of the radio control to be me-
morised and make sure that its LED flashes twice
before going off, to indicate that the procedure
was completed successfully.
6. Release all buttons.
7. Press the button used in step 5 twice in succession
to complete the memorisation process for the new
radio control. If the procedure was carried out
correctly, the B614 will open the beam, if permitted
by the operating mode that has been set.
LC/RC - MEMORISING THE FIRST RADIO
CONTROL
1. Press and keep pressed the + key (OPEN program-
ming) or - (CLOSE programming). After pressing
the button for about 5 seconds, the corresponding
radio LED (DL4 or DL5) will start to flash to indicate
that the radio code learning phase has started.
2. Release the button, from this moment E614 stays
in the learning phase for around 20 secs.
3. Make sure that the LED DL4 or DL5 on the board
is still flashing and press the button of the LC/RC
radio control that you wish to memorise for a few
seconds (the LED becomes steady). The LED
(DL4 or DL5) on the board goes on as a steady light
for 1 sec to then start flashing again for another 20
seconds during which it is possible to memorise
another radio control.
4. To memorise additional radio controls at a later stage,
