EYELA LTI- 400E Instruction Manual Download Page 47

Page: 47 / 62

In case of power failure (including the case that power

switch is turned off without stopping control) operations

after the recovery can be set.

Power recovery setting

1) Press

［

Set

］

key for longer than 5 seconds.

The mode enters into adjustment mode and

indicator displays [SnS] to enter into calibrating

displayed temperature mode.

2) Press

［▼］

key to enter into power recovery setting

mode

［

PoFF

］

3) Press

［

Set

］

key.

Indicator changes to display setting character

(blinking) of power recovery setting.

・「

Set key lamp

（

）」

lights up.

※

Setting character (blinking) is the character that

was used previous time. Factory default is [cont].

4) Press

［▲］

［▼］

key to select setting character.

※

Setting character changes in order as below;

［

cont

］：

Continues to control

［▲］↓ ↑［▼］

［

oFF

］：

Stopping control

［▲］↓ ↑［▼］

［

］：

Continues to control. Timer recounts

from the setting value.

5) Press

［

Set

］

key. Setting character (blinking) is

determined and indicator displays [buSE] to enter

into buzzer setting mode.

※

Changed setting character will not be available until

you press

［

Set

］

key.

※

To change another adjustment mode, press [

▲

] or

[

▼

] key to change the mode.

※

If you do not change other adjustment mode, press

[Set] key for longer than 5 seconds. Indicator

changes to display measured temperature again.

※

If no key operation is done for longer than a minute

while setting, the display changes to measured

temperature display again. In such a case, please

reset all the settings from 1).

４

How to operate power recovery setting

1) Press

［

Set

］

key for longer

than 5 sec. to enter into adjustment mode.

2) Moves to power

recovery setting

3) Setting power

recovery mode

4) Setting power

recovery mode

5) Determining power recovery

setting. Moves to buzzer setting mode.

-44-

Press 3 times

Run

Stop

Mode

Set

▼

▲

Def

h.m

℃

Alarm

Heating

Auto stop

Auto start

1Step

Defrost

24Hour

Pro.

○
○
○

○

SnS

●

Run

Stop

Mode

Set

▼

▲

Def

h.m

℃

Alarm

Heating

Auto stop

Auto start

1Step

Defrost

24Hour

Pro.

○
○
○

○

PoFF

●

Run

Stop

Mode

Set

▼

▲

Def

h.m

℃

Alarm

Heating

Auto stop

Auto start

1Step

Defrost

24Hour

Pro.

○
○
○

○

cont

●

Run

Stop

Mode

Set

▼

▲

Def

h.m

℃

Alarm

Heating

Auto stop

Auto start

1Step

Defrost

24Hour

Pro.

○
○
○

○

oFF

●

Run

Stop

Mode

Set

▼

▲

Def

h.m

℃

Alarm

Heating

Auto stop

Auto start

1Step

Defrost

24Hour

Pro.

○
○
○

○

buSE

●

○

Summary of Contents for LTI- 400E































































Search results

Summary of Contents for LTI- 400E

Reviews:

Related manuals for LTI- 400E

Brands by name

Popular brands

EYELA LTI- 400E, Instruction Manual

Search results

Summary of Contents for LTI- 400E

Reviews:

Related manuals for LTI- 400E

Brands by name

Popular brands