Extron electronics TouchLink TLP 350CV Installation Manual Download Page 50

Page: 50 / 51

Updating Firmware From a Web Browser

Power on a computer with internet access.

ensure the computer and the TLP 350CV are connected to the same network.

Download the firmware upgrade. (See

Obtaining the Firmware Update File on

page 41

.) Make a note of the folder where the firmware file is saved.

Open a browser and type the IP address of the TLP 350CV into the address box. The
browser opens the TouchLink panel web pages (see

Using the TouchLink Panel Web

Pages on page 19

TLP 350CV Default Web Page

Figure 32.

Firmware Upgrade Web Page

Click on the

Configuration

tab at the top of the page and then select

Firmware Upgrade

from the bar on the left.

Use the browse button to navigate to the firmware file that was saved in step

Click

Upload

. The Touchpanel screen will show the message “Firmware Uploading...

Please wait...”. when the firmware is uploaded, there is a message saying
“ReStarting...”. Once the firmware is installed, the panel can be calibrated using the
on-screen menus (see

Internal On-screen Menus on page 13

), or the TouchLink

panel web pages (see

Using the TouchLink Panel Web Pages on page 19

TLP 350CV • Reset Modes and Button Replacement

Summary of Contents for TouchLink TLP 350CV




















































Search results

Summary of Contents for TouchLink TLP 350CV

Reviews:

Related manuals for TouchLink TLP 350CV

Brands by name

Popular brands

Extron electronics TouchLink TLP 350CV, Installation Manual

Search results

Summary of Contents for TouchLink TLP 350CV

Reviews:

Related manuals for TouchLink TLP 350CV

Brands by name

Popular brands