manualshive.com logo in svg

Extron electronics TouchLink TLP 350CV, Installation Manual, Page: 15 / 51

Share
Download
Extron electronics TouchLink TLP 350CV Installation Manual Download Page 15

Mounting the Enclosure

CAUTION:

  The trim ring edges can easily be nicked or bent. exercise caution when 

handling and mounting the enclosure. 

1. 

Remove the edge grommet protecting the corners of the 
trim ring and the plastic film on the finished surfaces.

CAUTION:

  Do not use isopropyl alcohol or other 

solvents to clean the Cable Cubby. Strong 
solvents may ruin some finishes.

2. 

Lower the Cable Cubby enclosure into the cutout, feeding 
the cables hanging from the underside of the enclosure into 
the opening (see figure at right).

3. 

Install the table clamps onto the pins on the side of the 
enclosure at a height which allows the clamp to reach the 
underside of the tabletop.

4. 

Tighten the screws on the table clamps to secure the 
enclosure to the bottom of the table.

CAUTION:

  Do not overtighten the screw clamps. 

Overtightening can bend the horizontal 
flange of the clamp.

5. 

Tighten the wingnuts to lock the clamps in position. 

Front View

5. Tighten

    Wingnut

4. Tighten

    Screw

Table Clamp

Both Sides

PC

LAP

TOP

DVD

DOC

 CA

M

AUX

ILIA

RY

DISP

LAY

 ON

DISP

LAY

 OFF

AUT

O IM

AGE

VOL

UM

E  

VOL

UM

E  

Ext

ron

 

TLP 350CV • Mounting the TLP 350CV

9

Summary of Contents for TouchLink TLP 350CV




















































Reviews:

No comments