Extron electronics TouchLink TLP 350CV Installation Manual Download Page 16

Page: 16 / 51

Connecting the

Touch Panel

This section includes the following topics:

Connecting the TLP 350CV

Mounting the Power Supply (US models only)

Connecting the TLP 350CV

The rear panel of the TLP 350CV located on the bottom of the enclosure, provides all
required connections. The panel requires an IP Link controller for operation, but may be
configured without one connected.

Ground

+12 VDC

Orange Captive
Screw Connector

Tie Wrap

POWER

12V

1.0A MAX

LAN

VID / Y

PREVIEW INPUT

Straight-through Cable

(for connection to a switch, hub, or router)

End 1

End 2

Pin Wire Color

Pin

Wire Color

white-orange

orange

white-green

blue

white-blue

green

white-brown

brown

Crossover Cable

(for direct connection to a PC)

End 1

End 2

Pin Wire Color

white-orange

white-green

orange

green

white-green

white-orange

blue

white-blue

green

orange

white-brown

brown

Ethernet

RS-232

Projector

IPL 250

IP Link

Ethernet

Control Processor

Straight-through Cable

Crossover Cable

Source Device

INPUT

LAN

POWER
12V
500mA
MAX

1 2 3 4

COM 3

S G S G

TX RX

RELAY

COM1

TX RX

RTS CTS

COM 2

S G S G

TX RX

RELAY

Link
LED

Activity
LED

Composite

or S-Video

- OR -

TCP/IP

Network

FULL HIGH DEFINITION 1080P VIDEO OUTPUT

BLU-RAY DISC PLAYER

Extron

12V Power

Supply

UTP or STP CAT5 or better cable.
Terminate both ends identically, in
accordance with either the TIA/EIA T 568A
or the TIA/EIA T 568B wiring standard.

Connect a video source to
preview program material prior
to switching it to the display.

Crossover cable for
offline configuration
using GUI Configurator.

Straight-through cable for Global
Configurator and connection to
controllers via LAN.

Figure 4.

TLP 350CV Rear Panel

TLP 350CV • Connect the TLP 350CV

Summary of Contents for TouchLink TLP 350CV




















































Search results

Summary of Contents for TouchLink TLP 350CV

Reviews:

Related manuals for TouchLink TLP 350CV

Brands by name

Popular brands

Extron electronics TouchLink TLP 350CV, Installation Manual

Search results

Summary of Contents for TouchLink TLP 350CV

Reviews:

Related manuals for TouchLink TLP 350CV

Brands by name

Popular brands