evertz 5782DEC User Manual Download Page 27 | Manualshive

Page: 27 / 60

background image

5782DEC

Professional H.264 and MPEG-2 Decoder

VLPRO INTERFACE

Revision 1.0

Page - 17

Video PID:

This parameter displays the Video Packet ID (PID). The video PID allows the decoder to

sort the video packets in the transport stream to organize them for output.

Video Bitrate:

This parameter displays the video bitrate of the associated video stream.

Video Compression Type:

This parameter displays the video compression type of the associated

Transport Stream input.

Video Chroma Format:

This parameter displays the chroma format of the associated Transport

Stream input.

Video Resolution:

This parameter displays the video resolution of the associated Transport Stream

input.

Video Frame Rate:

This parameter displays the video frame rate of the associated Transport Stream

input.

Continuity Counter Error

Count:

This parameter displays the number of continuity errors counted.

Reset Count:

This parameter allows the user to reset the count of continuity errors.

Threshold:

This parameter displays the error threshold for continuity.

Status:

This indicator displays the fault status of the continuity; if it is red it indicates there is a fault

present in continuity.

Trap Enable:

This parameter allows the user to enable the monitoring of faults.

«
...
25
26
27
28
29
...
»

Summary of Contents for 5782DEC





























































Reviews:

No comments

Related manuals for 5782DEC

Brand: Parkside Pages: 77

Brand: Parkside Pages: 65

Brand: Humandata Pages: 10

Brand: StarTech.com Pages: 10

Brand: Monoprice Pages: 2

MOAB30-09HFN8-QRD0GW

Brand: Midea Pages: 172

THE-S55P3BB-USW

Brand: Tabuchi Electric Pages: 64

Brand: B&K Pages: 2

Brand: Odorox Pages: 11

Dazzle Digital Video Creator 90

Brand: Pinnacle Systems Pages: 53

Brand: Starview Pages: 6

Brand: RadioLink Pages: 11

IP4K-500 Series

Brand: Altimium Pages: 38

MAXX SST VEC054D

Brand: Vector Pages: 44

Brand: Teac Pages: 18

SUNNY HIGHPOWER PEAK1

Brand: SMA Pages: 16

Brand: Barco Pages: 4

Prizm 200750 Series

Brand: Moog Pages: 12

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands