evertz 5782DEC User Manual Download Page 51

Page: 51 / 60

5782DEC

Professional H.264 and MPEG-2 Decoder

WEBEASY

Revision 1.0

Page - 41

5.9.

SFP-ASI TRANSMIT CONTROL

Figure 5-12: WebEASY

– SFP Transmit Control Tab

SFP Transmit Control

SFP Transmit Output:

This parameter allows the user to set the mode of the SFP transmit feature,

to enable or disable transmitting on a specific output.

SFP Output IP Address:

This parameter allows the user to set the output IP address of the SFP

transmit stream if SFP Transmit is enabled.

SFP Output IP Port:

This parameter allows the user to set the output IP port number of the SFP

transmit stream if SFP Transmit is enabled.

PID Filter:

This parameter allows the user to enable PID filtering for the SFP transmit output stream.

Remove NULL Packets:

This parameter allows the user to enable the removal of NULL packets in

the SFP transmit stream.

Packet Rate Control:

This parameter allows the user to enable the packet rate control in the SFP

transmit stream.

Packet Bitrate:

This parameter displays the packet bitrate of data in the SFP transmit stream in

kbps.

BNC 4 Output:

This parameter allows the user to select the BNC <3,4> output type.

Summary of Contents for 5782DEC





























































Search results

Summary of Contents for 5782DEC

Reviews:

Related manuals for 5782DEC

Brands by name

Popular brands

evertz 5782DEC, User Manual

Search results

Summary of Contents for 5782DEC

Reviews:

Related manuals for 5782DEC

Brands by name

Popular brands