evertz 5782DEC User Manual Download | Manualshive

Page: 20 / 60

background image

5782DEC

Professional H.264 and MPEG-2 Decoder

Page - 10

Revision 1.0

VLPRO INTERFACE

Decoder Reboot:

This control allows the user to power cycle the decoder.

Load Factory Configuration:

This control allows the user to soft reset the decoder to the factory

settings.

Control Port:

Currently unused on 5782DEC platform.

Data Port <1,2> Control

IP Address:

This control allows the user to set the IP address on the Data Port. This control will also

display the currently set IP address.

Netmask:

This control allows the user to set the Netmask for the Data Port IP address. This control

will also display the currently set Netmask.

Gateway:

This control allows the user to set the Gateway for the Data Port. This control will also

display the currently set Gateway.

Data Port <1,2> Monitor

SFP Part Number:

This parameter returns the part number of the SFP located in the Data Port.

Port Link Status:

This parameter returns the link status for the data port, communicating to the user

whether the link is up or down.

Port Link Info:

This parameter returns the link status for the data port, containing information about

speed and duplex.

Receive Bandwidth:

When the link is Up, this parameter returns the receive bandwidth currently

being read on the Data Port. Reading is in kbps.

Transmit Bandwidth:

When the link is Up, this parameter returns the transmit bandwidth currently

being sent on the Data Port. Reading is in kbps.

Syslog Configuration

Syslog is a valuable tool for debugging the device operation. It is essentially serial readouts over IP,
sent to a dedicated server. If issues are present, Evertz can help install and setup a syslog server for
constant monitoring of the device activity.

External Syslog:

This parameter allows the user to enable or disable sending syslog information to

the configured external server.

Syslog Server IP:

This parameter allows the user to assign the external syslog server IP address.

This will be the address of a PC with the syslog server software installed (e.g. Kiwi Syslog Server).

Temperature

Temperature Monitor:

This displays the temperature of the module.

«
...
18
19
20
21
22
...
»

Summary of Contents for 5782DEC





























































Reviews:

No comments

Related manuals for 5782DEC

Brand: 3onedata Pages: 3

NDS NETWORK AUDIO PLAYER

Brand: NAIM Pages: 23

Brand: NAIM Pages: 36

Brand: NAIM Pages: 22

Brand: NAIM Pages: 8

HDX - REMOTE CONTROL CODE

Brand: NAIM Pages: 32

Brand: NAIM Pages: 2

Brand: NAIM Pages: 17

HDX - REMOTE CONTROL CODE

Brand: NAIM Pages: 8

Brand: YASKAWA Pages: 251

Brand: Generac Power Systems Pages: 64

Brand: Trace Engineering Pages: 2

Brand: ORO Pages: 18

CO-SinusUPS-400W

Brand: Adler Power Pages: 4

Brand: My Cable Mart Pages: 4

Brand: Balluff Pages: 2

Brand: AV Link Pages: 2

Brand: Metra Electronics Pages: 9

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands