Eventide Eclipse User Manual Download

Page: 19 / 68

Eclipse User Manual

Release 4.0.1

Page 17 of 66

Eclipse User Manual

Press the

PROGRAM

key again to jump “up” a level.



see page 28 for more

information

Press the



and



keys until the left side of the screen reads

Programs-Guitar

. Now you can access programs that were designed to

process guitars. Use the knob to select the program

FuzzADSRPreamp

Load the program by pressing the conspicuously labeled

<LOAD>

soft

key. You’re whisked away to the

HOT KEYS

area…

Too much distortion? Select the

(FUZZ)

soft key and use the knob to

select

out

Press the

HOT KEYS

key again to access more soft keys. Need more

funk? Select

(SENS)

and use the knob to tune in the “good stuff”!

OK, let’s load a different program that has an LFO so we can check out
the Eclipse’s tempo feature. Go back to the

PROGRAM

area and press the



soft key until the left side of the display reads

Programs-All

Use the knob to select

Dual Modfilter

and then

<LOAD>

it.

To insure that your tempo is behaving in a way that makes what follows
comprehensible, set

SETUP

TEMPO

(TAP SRC)

Internal

. You can

experiment with other settings (such as the all-important

Midiclock

) on your own time!

As an important aside, selecting

Off

would disable the tempo feature.

Return to the

HOT KEYS

area, play some music and tap the

TAP

key in

time. You’ll notice that the tempo is displayed (with less precision than
it truly possesses) and that the program’s modulating filters get all cozy
and synchronized with the music.

Select

HOT KEYS

(T_RATE)

and play around with different values, such

whole note

1/8 note

. Not bad…

Notice that if you alter

(T_RATE)

, the associated parameter

(RATE)

affected. It works like this: you select the source of the tempo as
described above. The tempo then “informs” all the

T_DELAY

T_RATE

and

T_xxxxx

parameters in the program that is loaded. They “filter” the

tempo information based on the rhythmic value you choose and
“inform” the actual

(DELAY)

(RATE)

parameters in the program in

their “native language” (e.g., milliseconds or Hertz).

The “unadorned”

(DELAY)

and

(RATE)

parameters are thus slaves to the

tempo and their associated

(T_xxxxx)

parameters. To relinquish control

back to the “unadorned” parameters, either turn off the tempo system as
described above, or turn off a given

(T_xxxxx)

parameter to

off

(just

keep spinning the knob to the right; you’ll get there!). Doing either ef-
fectively breaks one of the arrows shown to the right.



see pages 15 and 35 for more information

Summary of Contents for Eclipse





































































Search results

Summary of Contents for Eclipse

Reviews:

Related manuals for Eclipse

Brands by name

Popular brands

Eventide Eclipse, User Manual

Search results

Summary of Contents for Eclipse

Reviews:

Related manuals for Eclipse

Brands by name

Popular brands