Epygi QX1000 Administrator'S Manual Download

Page: 144 / 164

QX1000 Manual II: Administrator's Guide

Appendix: Conference Services for Moderators and Participants

QX1000; (SW Version 5.3.x)

143

Mute/Unmute

With this key combination, any participants in the conference may mute and unmute themselves during the conference.



Please Note:

You may accelerate dial out by a pound (#) sign at the end of your dialed number.

Call Codes available in the Auto Attendant:

For external IP calls addressed to the Auto Attendant following key combination is available to access and manipulate within Auto Attendant
services:

Incoming Call to Auto Attendant

Key Combination

Conferences Menu

- used to access conferences.

Conference ID

should be dialed here.

already in

Summary of Contents for QX1000





































































































































































Search results

Summary of Contents for QX1000

Reviews:

Related manuals for QX1000

Brands by name

Popular brands

Epygi QX1000, Administrator'S Manual

Search results

Summary of Contents for QX1000

Reviews:

Related manuals for QX1000

Brands by name

Popular brands