manualshive.com logo in svg

Epson Stylus Color C60, Service Manual

The Epson Stylus Color C60 Setup Manual can be conveniently downloaded for free from our website. This comprehensive manual provides step-by-step instructions on setting up and configuring your printer to ensure optimal performance. Get ready to experience hassle-free printing with the Epson Stylus Color C60.

Share
Download
background image

COMTENTS

PRODUCT DESCRIPTION

FEATURES .................................................................................................... 4

SPECIFICATIONS.......................................................................................... 5

Physical Specification................................................................................ 5
Printing Specification................................................................................. 5
Paper Feeding........................................................................................... 6
Paper Specification ................................................................................... 7
Printing Area............................................................................................ 10
Ink Cartridge Specification ...................................................................... 11
Electric Specification ............................................................................... 13
Environmental Condition ......................................................................... 14
Reliability ................................................................................................. 14
Safety Approvals ..................................................................................... 14
Acoustic Noise......................................................................................... 15
CE Marking.............................................................................................. 15

INTERFACE ................................................................................................. 16

Parallel Interface (Forward Channel) ...................................................... 16
Parallel Interface (Reserve Channel) ...................................................... 18
USB Interface .......................................................................................... 20
Prevention Hosts of Data Transfer Time-out........................................... 21
Interface Selection................................................................................... 21
IEEE1284.4 Protocol ............................................................................... 21

PANEL CONTROL ....................................................................................... 22

Indicators (LEDs)..................................................................................... 22
Panel Functions....................................................................................... 22
Printer Condition and Panel Status ......................................................... 23
Error Status ............................................................................................. 23
Printer Initialization .................................................................................. 24

Operating Principles

Overview ...................................................................................................... 26

Printer Mechanism .................................................................................. 26
Printhead ................................................................................................. 27
Carriage Mechanism ............................................................................... 30
Paper Loading/Feeding Mechanism ....................................................... 31
Ink System Mechanism ........................................................................... 36
Ink Sequence .......................................................................................... 39

Electrical Circuit Operating Principles .......................................................... 41

C417 PSB/PSE board, C482 PSH board ................................................ 42
C418 MAIN/MAIN-B/C429 Main Board ................................................... 46
C483/C484 MAIN-B Board ...................................................................... 52

Troubleshooting

Overview ...................................................................................................... 59

Troubleshooting with LED Error Indications
        and Status Monitor 3 Message............................................................. 60

Unit Level Troubleshooting........................................................................... 65

Disassembly and Assembly

Overview ...................................................................................................... 86

Precautions ............................................................................................. 86
Tools ....................................................................................................... 88

Screws..................................................................................................................  88

Work Completion Check ......................................................................... 89

Difference on Printer Machanism between
        SC60 and SC61/C62 ............................................................................ 90

Disassembly ................................................................................................. 92

Upper housing removal ........................................................................... 93
Printhead removal ................................................................................... 95
CR unit removal ...................................................................................... 97

Summary of Contents for Stylus Color C60





























































































































































































Reviews:

No comments

Related manuals for Stylus Color C60

Oki C7300 Replacement Instructions preview
C7300
Brand: Oki Pages: 2
Washtech CD180 Operator'S Manual preview
CD180
Brand: Washtech Pages: 20
i-box Essence Manual preview
Essence
Brand: i-box Pages: 24
Dakota Alert WTS-1000 Manual preview
WTS-1000
Brand: Dakota Alert Pages: 2
DAINCUBE DTP10-P Hardware User Manual preview
DTP10-P
Brand: DAINCUBE Pages: 38
Icebreeze PORTABLE AIR CONDITIONER & COOLER Owner'S Manual preview
PORTABLE AIR CONDITIONER & COOLER
Brand: Icebreeze Pages: 12
Kathrein HDP 171 Notice D'Utilisation preview
HDP 171
Brand: Kathrein Pages: 52
Xante CL30 Setup Manual preview
CL30
Brand: Xante Pages: 25
Xerox Phaser 7300 Maintenance Manual preview
Phaser 7300
Brand: Xerox Pages: 11
Xerox Phaser 6200 Setup Manual preview
Phaser 6200
Brand: Xerox Pages: 30
Xerox Versant 4100 Press Quick Start Manual preview
Versant 4100 Press
Brand: Xerox Pages: 68
Xerox Phaser 860 Brochure & Specs preview
Phaser 860
Brand: Xerox Pages: 4
Xerox Phaser 7300B Brochure & Specs preview
Phaser 7300B
Brand: Xerox Pages: 4
Xerox 4004 Instructions preview
4004
Brand: Xerox Pages: 2
Xerox Versant 2100 Press Quick Start Manual preview
Versant 2100 Press
Brand: Xerox Pages: 68
Zircon StudSensor HD25 Instructions preview
StudSensor HD25
Brand: Zircon Pages: 2
Oliver 2218 User'S Operating And Instruction Manual preview
2218
Brand: Oliver Pages: 15
HIKVISION DS-KABD8003-RS3 Quick Start Manual preview
DS-KABD8003-RS3
Brand: HIKVISION Pages: 3

Brands by name

Popular brands

Load more brands