Epson Stylus Color C60 Service Manual Download Page 85

Page: 85 / 188

EPSON Stylus C50/C60/C61/C62

Revision C

Troubleshooting

Unit Level Troubleshooting

Power on

Anywhere

The printer does not perform the ink
replacement CL and the error is
indicated with LEDs and STM3.

Ink cartridge

1. Check if ink cartridge can be used by install it to other

printer.

1. Replace the ink cartridge with brand-new

one.

The printer does not perform the printing
operation and the error is indicated with
LEDs and STM3.

Ink cartridge

1. Check if the ink is remaining in the I/C.

2. Check if the ink cartridge can be used by install it to other

printer.

1. Replace the ink cartridge with brand-new

one.

2. Replace the ink cartridge with brand-new

one.

Table 3-14. Error regarding paper loading / ejecting without LEDs and STM3

Error condition

LED indication

STM3 message

Occurrence

timing

CR position at the

power on timing

Unit/Part name

Possible cause

Check table

Multiple papers

are always loaded

Power : -

Error : -

No appear

Operation

ASF unit

The Tension spring 29.1 comes off.

Refer to Table 3-15

5” x 8” index card

is not ejected

correctly

Front frame

The Eject roller holder (white part) comes off.

Table 3-15. Check point for multiple papers are always loaded without LEDs and STM3

Occurrence

timing

CR position

Detailed phenomenon

Defective

unit/part name

Check point

Remedy

Operation

Any error condition is not indicated with
the LEDs and STM3. But, multiple
papers are always loaded from ASF unit.

ASF unit

1. Check if the Paper return plate operates correctly in the

paper loading sequence.

1. Reassemble the Tension spring 29.1 between

the ASF frame and the Paper return plate.

Any error condition is not indicated with
the LEDs and STM3. But, 5” x 8” index
card is not ejected correctly.

Front frame

1. Check if the Eject roller holder (white part) comes off.

2. Reassembly the Eject roller holder (white

part).

Table 3-13. Check point for the error before the initial ink charge according to each phenomenon

Occurrence

timing

CR position

Detailed phenomenon

Defective

unit/part name

Check point

Remedy

Torsion spring 29.1

Summary of Contents for Stylus Color C60





























































































































































































Search results

Summary of Contents for Stylus Color C60

Reviews:

Related manuals for Stylus Color C60

Brands by name

Popular brands

Epson Stylus Color C60, Service Manual

Search results

Summary of Contents for Stylus Color C60

Reviews:

Related manuals for Stylus Color C60

Brands by name

Popular brands