Epson Stylus Color C60 Service Manual Download Page 91

Page: 91 / 188

EPSON Stylus C50/C60/C61/C62

Revision C

Troubleshooting

Unit Level Troubleshooting

Operation

Vertical banding appears against the CR
movement direction. And, it looks like
uneven printing.

Front frame

1. Check if the grease is enough on the surface of the

Front frame.

2. Check if the surface of the Front frame is flat.

1. Clean the surface of the Front frame with the

dry soft cloth and lubricate G-58 on its shaft.
Refer to Figure 6-6/Figure 6-7.

2. Replace the Front frame with new one.

Printhead

1. Check if each segment is printed correctly in the nozzle

check pattern.

1. Perform the printhead cleaning and check the

nozzle check pattern.
If the problem is not solved, replace the
printhead with new one.

Micro banding appears horizontally
against the CR movement direction and
it appears with the same width.

[Note]
If the problem is not solved, replace the
PF motor with new one.

PF roller unit

1. Check if there is any foreign material on the surface of the

PF roller.

2. Check if the PF roller is damaged

3. Check if the Spur gear 60 is damaged.

1. Clean the surface of the PF roller carefully

with the soft cloth.

2. Replace the Printer mechanism with new one.

3. Replace the Printer mechanism with new one.

Printer driver &

exclusive paper

1. Check if the suitable paper is used according to the printer

driver setting.

1. Use the suitable paper according to the printer

driver setting.

Printhead

1. Check if each segment is printed correctly in the nozzle

check pattern.

1. Perform the printhead cleaning and check the

nozzle check pattern.
If the problem is not solved, replace the
printhead with new one.

Star wheel mark against the CR
movement direction

Front frame

1. Check if the Star wheel comes off.

2. Check if the surface of the Front frame is flat.

1. Reassemble the Star wheel correctly.

2. Replace the Front frame with new one.

Paper eject roller

unit

1. Check if the Paper eject roller comes off from the Lower

housing.

1. Reassemble the Paper eject roller correctly.

Table 3-19. Check point for the poor printing quality

Occurrence

timing

CR position

Detailed phenomenon

Defective

unit/part name

Check point

Remedy

G-58 lubrication

CR movement

direction

Summary of Contents for Stylus Color C60





























































































































































































Search results

Summary of Contents for Stylus Color C60

Reviews:

Related manuals for Stylus Color C60

Brands by name

Popular brands

Epson Stylus Color C60, Service Manual

Search results

Summary of Contents for Stylus Color C60

Reviews:

Related manuals for Stylus Color C60

Brands by name

Popular brands