Epson Stylus Color C60 Service Manual Download Page 84

Page: 84 / 188

EPSON Stylus C50/C60/C61/C62

Revision C

Troubleshooting

Unit Level Troubleshooting

Table 3-12. Error condition before the initial ink charge/the I/C replacement CL and possible cause & Ink out error and possible cause

Error condition

LED indication *

STM3 message

Occurrence

timing

CR position at the

power on timing

Unit/Part name

Possible cause

Check table

Error before the

initial ink charge is

performed

Power : On

Error : On

Incorrectly installed

cartridge

Power on

Inside HP

Ink cartridge

The 1st ink cartridge is defective.

Refer to Table 3-13

Main board

The incorrect data is stored into the specific address of the
EEPROM.

Error before the ink

replacement CL is

performed

Power : On

Error : On

Installed ink cartridge

cannot be recognized

Anywhere

Ink cartridge

2nd or more ink cartridges is defective.

The ink cartridge is compatible or counterfeit one.

Power : On

Error : On

Black & Color ink

cartridge not installed

Ink cartridge

The ink cartridge is defective.

The ink cartridge is compatible or counterfeit one.

Ink out error

Power : On

Error : On

Black & Color ink out

Ink cartridge

The ink amount in I/C is end condition.

The ink cartridge is defective.

* The above LED indication timing is at the CR home position. When the CR unit moves to the I/C replacement position with the I/C replacement sequence, this indication will change to blink
condition.

Table 3-13. Check point for the error before the initial ink charge according to each phenomenon

Occurrence

timing

CR position

Detailed phenomenon

Defective

unit/part name

Check point

Remedy

Power on

Inside HP

The printer does not perform the initial
ink charge and the error is indicated with
LEDs and STM3.

Ink cartridge

1. Check if the ink cartridge can be used by install it to

other printer.

1. Replace the ink cartridge with the brand-new

one.

Main board

1. Check if the incorrect data is stored into the 3C<H>

address of the EEPROM on the Main board.

1. Write the 9E<H> data into the 3C<H>

address of the EEPROM by using the Dump
exe. program in the Adjustment program.

Summary of Contents for Stylus Color C60





























































































































































































Search results

Summary of Contents for Stylus Color C60

Reviews:

Related manuals for Stylus Color C60

Brands by name

Popular brands

Epson Stylus Color C60, Service Manual

Search results

Summary of Contents for Stylus Color C60

Reviews:

Related manuals for Stylus Color C60

Brands by name

Popular brands