Epson Stylus Color C60 Service Manual Download Page 109

Page: 109 / 188

EPSON Stylus C50/C60/C61/C62

Revision C

Disassembly and Assembly

Disassembly

101

4.3.5 ASF unit removal

Remove the Upper housing from the printer. (Refer to Section 4.3.1)

Remove three screws (C.B.S. SCREW 3x6 F/Zn, C.B.S-TITE (P4) 3x6 F/Zn,
C.B.P-TITE 3x8 F/Zn) for securing the ASF unit to the Main frame, and remove
the ASF unit with pulling up slightly to the backside of the printer..

Figure 4-20. Screw position for removing the ASF unit

Remove the Compression spring 2.50 located between the ASF frame and the
Hopper, and remove the Hopper from the ASF unit.

Figure 4-21. Compression spring 2.50 and the Hopper removal

Remove the Torsion spring 29.1 from the bottom of the ASF frame and the Pad
holder (Paper return plate).

Figure 4-22. Torsion spring 29.1 setting position

C.B.S. SCREW, 3x6, F/Zn

C.B.P-TITE, 3x8, F/Zn

C.B.S-TITE (P4), 3x6, F/Zn

Pad holder

ASF frame

Compression spring 2.50

ASF hopper

Torsion spring 29.1

ASF frame

Summary of Contents for Stylus Color C60





























































































































































































Search results

Summary of Contents for Stylus Color C60

Reviews:

Related manuals for Stylus Color C60

Brands by name

Popular brands

Epson Stylus Color C60, Service Manual

Search results

Summary of Contents for Stylus Color C60

Reviews:

Related manuals for Stylus Color C60

Brands by name

Popular brands