Epson Stylus Color C60 Service Manual Download Page 83

Page: 83 / 188

EPSON Stylus C50/C60/C61/C62

Revision C

Troubleshooting

Unit Level Troubleshooting

Table 3-10. Communication error condition and possible cause

Error condition

LED indication

STM3 message

Occurrence

timing

CR position at the

power on timing

Unit/Part name

Possible cause

Check table

Communication

error

Power : Off

Error : Off

Communication error

Power on

Anywhere

Main board

The Main board is defective.

Refer to Table 3-11

Power supply board

The Power supply connector cable comes off.

The Power supply connector cable is damaged.

The Power supply board is defective.

Operation

Main board

The incorrect data is stored into the specific address of the
EEPROM.

Parallel cable

The parallel cable does not support the bi-directional
transportation.

Printer driver

The suitable printer driver is not installed into the PC.

Table 3-11. Check point for the communication error according to each phenomenon

Occurrence

timing

CR position

Detailed phenomenon

Defective

unit/part name

Check point

Remedy

Power on

Anywhere

When turning on the power, the printer
does not operate at all.

Power supply

board

1. Check if the Power supply connector cable is connected

to CN2 on the Main board.

2. Check if the Power supply connector cable is damaged.

1. Connect the Power supply connector cable to

CN2 on the Main board.

2. Replace the Power supply board with new one.

* If the problem is not solved, replace the
Main board with new one.

Operation

When turning on the power, the power
on sequence is performed correctly. But,
when any printer job is sent to printer,
the communication error is indicated
with STM3.

Main board

1. Check if the incorrect model name is stored into the

5F<H> address of the EEPROM on the Main board.

1. Write the 00<H> data into the 5F<H> address

of the EEPROM by using the Dump eve.
program in the Adjustment program.

Parallel/USB cable

1. Check if the Parallel/USB cable is connected between

the printer and the PC.

1. Connect the Parallel/USB cable to the printer

and the PC.

Printer driver

1. Check if the Stylus C60 printer driver is used for the

printer job.

1. Install the Stylus C60 printer driver in the PC.

Summary of Contents for Stylus Color C60





























































































































































































Search results

Summary of Contents for Stylus Color C60

Reviews:

Related manuals for Stylus Color C60

Brands by name

Popular brands

Epson Stylus Color C60, Service Manual

Search results

Summary of Contents for Stylus Color C60

Reviews:

Related manuals for Stylus Color C60

Brands by name

Popular brands