Epson Stylus Color C60 Service Manual Download Page 103 | Manualshive

Page: 103 / 188

background image

EPSON Stylus C50/C60/C61/C62

Revision C

Disassembly and Assembly

Disassembly

95

4.3.2 Printhead removal

1.

Remove the Upper housing from the printer. (Refer to Section 4.3.1)

2.

Open the Cover cartridge, and remove the both black and color ink cartridges.

3.

Remove the both Cover cartridges from the CR unit.

4.

Release two hooks for securing the Head FFC holder, and remove the Head FFC
holder from the CR unit.

Figure 4-7. Head FFC holder removal

5.

Remove two screws (C.B.P-TITE SCREW 3x8 F/Zn, +BIND B-TITE SEMS W2
2.5x5 F/Zb) for tightening the Printhead, and remove the Printhead from the CR
unit in the order indicated in the following figure.

Figure 4-8. Printhead removal

6.

Disconnect the Head FFC from the connector on the Printhead.

Hooks for Head FFC

Spacer FFC

Cable holder

The length of the Head FFC is

difference among each model.

SC61/C62 > SC60 > SC50

C.B.P-TITE SCREW, 3x8, F/Zn

+BIND B-TITE SEMS, W2 2.5x5, F/Zb

(This screw is used only for the Stylus C60)

1

2

This figure is the Stylus Photo 810/820. There is a
difference of the Printhead between the Stylus
C60 and the Stylus Photo 810/820.
- Stylus C50/C60/C61/C62 : Printhead for 4col.
- Stylus Photo 810/820 : Printhead for 6col.

«
...
101
102
103
104
105
...
»

Summary of Contents for Stylus Color C60





























































































































































































Reviews:

No comments

Related manuals for Stylus Color C60

Brand: YOELEO Pages: 3

imageRUNNER 2545i

Brand: Canon Pages: 37

Brand: Canon Pages: 36

Brand: Canon Pages: 62

Brand: GOgroove Pages: 9

Brand: Alpine Pages: 8

Brand: Manfrotto Pages: 36

Brand: Baumer Pages: 3

X-ACT CONTOUR 53491

Brand: HUSKY LINERS Pages: 2

Brand: BIXOLON Pages: 29

OADM 21I6480/S14F

Brand: Baumer Pages: 4

Smartmatic 9108011013

Brand: Nobile Pages: 2

Brand: MELINERA Pages: 44

Brand: Badabulle Pages: 21

Brand: Omnimount Pages: 16

Brand: Sandstrom Pages: 12

Brand: Pyle Pages: 2

Brand: Xerox Pages: 29

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands