Epson Stylus 1500 Service Manual Download Page 31 | Manualshive

Page: 31 / 185

background image

Printer Initialization

This printer has three initialization types: hardware, software, and panel.

Hardware Initialization

Hardware initialization is performed when you turn on the printer or when the host sends the INIT
signal to the parallel interface. The following functions are executed:

❏

The printer mechanism is initialized.

❏

The input data buffer is cleared.

❏

Downloaded character definitions are cleared.

❏

The print buffer is cleared.

❏

Default values are set.

Software Initialization

Software initialization occurs when the printer receives the ESC @ command. The following
functions are executed:

❏

The print buffer is cleared.

❏

Default values are set.

Note:

The last panel settings are kept after software initialization.

Panel Initialization

Panel initialization is performed when you press the

Load/Eject

button while holding down the

Alt

button. The following functions are executed:

❏

The input data buffer is cleared.

❏

The print buffer is cleared.

❏

Default values are set.

Note:

The last panel settings are kept after panel initialization.

Monochrome Printing Mode

This printer has a monochrome printing function that allows printing to continue with black ink
when the color ink cartridge is out or not installed. This function is selected by the printer driver
setting. To enter monochrome printing mode, turn the

Power

button off and back on again.

Notes:

1. Once the printer has entered this function, print data must be re-sent.

2. The color select command (ESC r) is ignored.

Printer Features

1-24

EPSON Stylus 1500 Service Manual

«
...
29
30
31
32
33
...
»

Summary of Contents for Stylus 1500


























































































































































































Reviews:

No comments

Related manuals for Stylus 1500

Brand: Panasonic Pages: 54

Brand: Panasonic Pages: 12

Brand: Panasonic Pages: 12

Brand: Panasonic Pages: 8

KX-FLB851 - All-in-One Flatbed Laser Fax

Brand: Panasonic Pages: 28

Brand: Panasonic Pages: 2

Brand: Panasonic Pages: 12

Brand: Panasonic Pages: 12

Brand: Oce Pages: 90

Brand: Xante Pages: 31

Brand: Oce Pages: 222

Brand: Sagem Pages: 126

Brand: Oki Pages: 198

Brand: SEWOO Pages: 13

Brand: Xerox Pages: 214

Brand: Cardco Pages: 28

VersaUV LEJ-640

Brand: Roland Pages: 321

Brand: Oki Pages: 4

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands